Nissan Altima 2007-2012 Service Manual: B1065 – B1068, B1070 – B1073 passenger airbag module
Description
DTC B1065 – B1068, B1070 – B1073 PASSENGER AIR BAG MODULE
The passenger air bag module is dual stage and wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor for opens and shorts in detected lines to the passenger air bag module.
PART LOCATION
Refer to SRC-7, "SRS Component Parts Location".
DTC Logic
DTC DETECTION LOGIC
With CONSULT-lll
Without CONSULT-lll
DTC CONFIRMATION PROCEDURE (With CONSULT-lll)
1.INSPECTION START
Turn ignition switch ON.
>> GO TO 2.
2.CHECK SELF-DIAG RESULT
Check for the DTC on CONSULT-lll.
Is the DTC detected? YES >> Refer to SRC-20, "Diagnosis Procedure (Component Diagnosis)".
NO >> Inspection End.
DTC CONFIRMATION PROCEDURE (Without CONSULT-lll)
NOTE: SRS will not enter diagnosis mode if no malfunction is detected in user mode.
1.IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 2
2.IGNITION SWITCH
After air bag warning lamp lights for 7 seconds, turn ignition switch OFF within 1 second.
>> GO TO 3
3.WAIT TIME
Wait more than 3 seconds.
>> GO TO 4
4.REPEAT STEPS
Repeat steps 1 to 3 twice.
>> GO TO 5
5.IGNITION SWITCH
Turn ignition switch ON.
>> GO TO 6
6.DIAGNOSTIC MODE
SRS system is now in diagnostic mode and AIR BAG warning lamp flashes. Refer to SRC-70, "Trouble Diagnosis without CONSULT-III".
>> END
Diagnosis Procedure (Component Diagnosis)
Recheck SRS after each replacement.
1.HARNESS CONNECTOR
Is there any visible damage to the connector? YES or NO
YES >> Replace the harness.
NO >> GO TO 2
2.WIRING HARNESS
Is there any visible damage to the harness? YES or NO YES >> Replace the harness.
NO >> GO TO 3
3.FRONT PASSENGER AIR BAG MODULE
Replace the front passenger air bag module. Refer to SR-10, "Removal and Installation".
>> GO TO 4
4.AIR BAG DIAGNOSIS SENSOR UNIT
Replace the air bag diagnosis sensor unit. Refer to SR-17, "Removal and Installation".
>> GO TO 5
5.RELATED HARNESS
Replace the related harness.
>> END
B1049 – B1052, B1054 – B1057 driver airbag module
Description DTC B1049 – B1052, B1054 – B1057 DRIVER AIRBAG MODULE The driver air bag module is dual stage and wired to the air bag diagnosis sensor unit through the spiral cable. The air ba ...B1134 – B1137 side airbag module LH
Description DTC B1134 – B1137 FRONT LH SIDE AIR BAG MODULE The front LH side air bag module is wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor for ope ...Other materials:
Refrigerant pressure sensor
Description
The refrigerant pressure sensor is installed at the condenser of the air
conditioner system. The sensor uses an
electrostatic volume pressure transducer to convert refrigerant pressure to
voltage. The voltage signal is sent
to ECM, and ECM controls cooling fan system.
Component ...
B2608 starter relay
Description
Located in IPDM E/R, it runs the starter motor. The starter relay is turned
ON by the BCM when the ignition
switch is in START position. IPDM E/R transmits the starter relay ON signal to
BCM via CAN communication.
DTC Logic
DTC DETECTION LOGIC
NOTE:
• If DTC B2608 is displa ...
Roof side molding
Removal and Installation
1. Body side outer panel
2. Windshield
3. Roof
REMOVAL
1. Lift and twist the roof side molding up from the rear edge.
2. Disconnect the roof side molding from the clips, and remove the roof side
molding.
INSTALLATION
Installation is in the reverse order of ...