Nissan Altima 2007-2012 Service Manual: Front door speaker (sedan)

Description

The audio unit sends audio signals to the BOSE speaker amp. The BOSE speaker amp. amplifies the audio signals before sending them to the front door speakers using the audio signal circuits.

Diagnosis Procedure

1.HARNESS CHECK

1. Disconnect BOSE speaker amp. connector B121 and suspect speaker connector.

2. Check continuity between BOSE speaker amp. harness connector B121 (A) and suspect speaker harness connector (B).


3. Check continuity between BOSE speaker amp. harness connector


3. Check continuity between BOSE speaker amp. harness connector B121 (A) and ground.

Are continuity test results as specified?


Are continuity test results as specified? YES >> GO TO 2

NO >> • Check connector housings for disconnected or loose terminals.

• Repair harness or connector.

2.FRONT DOOR SPEAKER SIGNAL CHECK

1. Connect BOSE speaker amp. connector B121 and suspect speaker connector.

2. Turn ignition switch to ACC.

3. Push “POWER” switch.

4. Check the signal between BOSE speaker amp. harness connector B121 terminals with CONSULT-III or oscilloscope.


Is audio signal voltage as specified?


Is audio signal voltage as specified? YES >> Replace suspect speaker. Refer to AV-442, "Removal and Installation".

NO >> GO TO 3

3.HARNESS CHECK

1. Disconnect AV control unit connector M47 and BOSE speaker amp. connector B121.

2. Check continuity between audio unit harness connector M47 (A) and BOSE speaker amp. harness connector B121 (B).


3. Check continuity between AV control unit harness connector


3. Check continuity between AV control unit harness connector M47 (A) and ground.

Are continuity test results as specified?


Are continuity test results as specified? YES >> GO TO 4

NO >> • Check connector housings for disconnected or loose terminals.

• Repair harness or connector.

4.FRONT DOOR SPEAKER SIGNAL CHECK

1. Connect AV control unit connector and BOSE speaker amp.

connector.

2. Turn ignition switch to ACC.

3. Push “POWER” switch.

4. Check the signal between AV control unit harness connector terminals with CONSULT-III or oscilloscope.


Are the audio signal voltage readings as specified?


Are the audio signal voltage readings as specified? YES >> Replace BOSE speaker amp. Refer to AV-438, "Removal and Installation - Sedan".

NO >> Replace AV control unit. Refer to AV-437, "Removal and Installation".

    Door speaker (coupe)
    Description The audio unit sends audio signals to the BOSE speaker amp. The BOSE speaker amp. amplifies the audio signals before sending them to the door speakers using the audio signal circuit ...

    Front tweeter (coupe)
    Description The audio unit sends audio signals to the BOSE speaker amp. The BOSE speaker amp. amplifies the audio signals before sending them to the front tweeters using the audio signal circuit ...

    Other materials:

    Control valve
    Exploded View COMPONENT PARTS LOCATION 1. Transaxle assembly 2. Control valve 3. Bracket 4. O-ring 5. Oil strainer assembly 6. Magnet 7. Oil pan bolt 8. Oil pan 9. Oil pan gasket 10. Lock nut 11. Washer 12. Manual plate 13. Collar 14. Lip seal 15. Snap ring A. CVT unit connector ...

    P1550 battery current sensor
    Description The power generation voltage variable control enables fuel consumption to be decreased by reducing the engine load which is caused by the power generation of the generator. The battery current sensor is installed to the battery cable at the negative terminal. The sensor measures ...

    Auto operation does not operate but manual operates normally (driver side)
    Diagnosis Procedure 1. PERFORM INITIALIZATION PROCEDURE Perform initialization procedure. Refer to PWC-21, "POWER WINDOW MAIN SWITCH : Special Repair Requirement". Is the inspection result normal? YES >> GO TO 2 NO >> Repair or replace the malfunctioning parts. 2. CH ...