Nissan Altima (L32) 2007-2012 Service Manual ≻ Power window control system lh&rh front anti-pinch-coupe ≻ Component diagnosis ≻ Encoder ≻ Passenger side

Nissan Altima (L32) 2007-2012 Service Manual: Passenger side

Description

Detects condition of the power window motor RH operation and transmits to power window and door lock/ unlock switch RH as pulse signal.

Component Function Check

1. CHECK ENCODER OPERATION

Does door glass RH perform AUTO open/close operation normally when operating power window and door lock/unlock switch RH? Is the inspection result normal? YES >> Encoder operation is OK.

NO >> Refer to PWC-209, "PASSENGER SIDE : Diagnosis Procedure".

Diagnosis Procedure

1. CHECK ENCODER SIGNAL

1. Turn ignition switch ON.

2. Check signal between power window and door lock/unlock switch RH connector and ground with oscilloscope.

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> GO TO 2

2. CHECK POWER WINDOW MOTOR RH POWER SUPPLY

1. Turn ignition switch ON.

2. Check voltage between power window motor RH connector and ground.

Is the measurement value within the specification? YES >> GO TO 4

NO >> GO TO 3

3. CHECK HARNESS CONTINUITY 1

1. Turn ignition switch OFF.

2. Disconnect power window and door lock/unlock switch RH and power window motor RH.

3. Check continuity between power window and door lock/unlock switch RH connector (A) and power window motor RH connector (B).

4. Check continuity between power window and door lock/unlock switch RH connector (A) and ground.

Is the inspection result normal? YES >> Replace power window and door lock/unlock switch RH. Refer to PWC-291, "Removal and Installation".

After that, refer to PWC-201, "PASSENGER SIDE : Special Repair Requirement".

NO >> Repair or replace harness.

4. CHECK GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect power window motor RH.

3. Check continuity between power window motor RH connector and ground.

Is the inspection result normal? YES >> GO TO 6

NO >> GO TO 5

5. CHECK HARNESS CONTINUITY 2

1. Disconnect power window and door lock/unlock switch RH.

2. Check continuity between power window and door lock/unlock switch RH connector (A) and power window motor RH connector (B).

Is the inspection result normal? YES >> Replace power window and door lock/unlock switch RH.

Refer to PWC-291, "Removal and Installation". After that, refer to PWC-201, "PASSENGER SIDE : Special Repair Requirement".

NO >> Repair or replace harness.

6. CHECK HARNESS CONTINUITY 3

1. Disconnect power window and door lock/unlock switch RH.

2. Check continuity between power window and door lock/unlock switch RH connector (A) and power window motor RH connector (B).

3. Check continuity between power window and door lock/unlock switch RH connector (A) and ground.

Is the inspection result normal? YES >> Replace power window motor RH. Refer to GW-19, "Removal and Installation". After that, refer to PWC-205, "PASSENGER SIDE : Special Repair Requirement".

NO >> Repair or replace harness.

Driver side

Description Detects condition of the power window motor LH operation and transmits to main power window and door lock/unlock switch as pulse signal. Component Function Check 1. CHECK ENCO ...

Door switch

Description Detects door open/close condition and transmits the signal to BCM. Component Function Check 1. CHECK DOOR SWITCH INPUT SIGNAL Check (“DOOR SW-DR” and “DOOR SW-AS”) in “DATA ...

Other materials:

Passenger side
Description Main power window and door lock/unlock switch, power window and door lock/unlock switch RH and BCM transmit and receive the signal by power window serial link. The signal mentioned below is transmitted from BCM to main power window and door lock/unlock switch and power window a ...

Axle and suspension parts
Inspection Check front and rear axle and suspension parts for excessive play, cracks, wear or other damage. • Shake each wheel to check for excessive play. • Check wheel bearings for smooth operation. • Check axle and suspension nuts and bolts for looseness. • Check strut (sho ...

P0340 CMP Sensor (phase)
Description The camshaft position sensor (PHASE) senses the retraction of camshaft (INT) to identify a particular cylinder. The camshaft position sensor (PHASE) senses the piston position. When the crankshaft position sensor (POS) system becomes inoperative, the camshaft position sensor (PHAS ...