Nissan Altima Owners Manual: Moonroof (if so equipped)

AUTOMATIC MOONROOF


AUTOMATIC MOONROOF

switch is placed in the ON position. The automatic moonroof is operational for a period of time, even if the ignition switch is placed in the ACC or OFF position. If the drivers door or the front passengers door is opened during this period of time, the power to the moonroof is canceled.

Sliding the moonroof

To fully open or close the moonroof, push the switch to the open 2 or close 1 position and release it; it need not be held. The roof will automatically open or close all the way. To stop the roof, push the switch once more while it is opening or closing.

Tilting the moonroof

To tilt up, first close the moonroof, then push the switch to the tilt up position 1 and release it; it need not be held. To tilt down the moonroof, push the switch to the tilt down position 2 .

Resetting the moonroof switch If the moonroof does not operate properly, perform the following procedure to initialize the moonroof operation system.

1. If the moonroof is open, close it fully by repeatedly pushing the moonroof switch to the close position 1 to tilt the moonroof up.

2. Push and hold the switch to the close position 1 .

3. Release the moonroof switch after the moonroof moves slightly up and down.

4. Push and hold the switch to the open position 2 to fully tilt the moonroof down.

5. Check if the moonroof switch operates normally.

If the moonroof does not operate properly after performing the procedure above, have your vehicle checked by a NISSAN dealer.

Auto-reverse function (when closing or tilting down the moonroof)

The auto-reverse function can be activated when the moonroof is closed or tilted down by automatic operation when the ignition switch is placed in the ON position or for a period of time after the ignition switch is placed in the OFF position.

Depending on the environment or driving conditions, the auto-reverse function may be activated if an impact or load similar to something being caught in the moonroof occurs.

WARNING

There are some small distances immediately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., inside the vehicle before closing the moonroof.

When closing:

If the control unit detects something caught in the moonroof as it moves to the front, the moonroof will immediately open backward.

When tilting down:

If the control unit detects something caught in the moonroof as it tilts down, the moonroof will immediately tilt up.

If the auto-reverse function malfunctions and repeats opening or tilting up the moonroof, keep pushing the tilt down switch within 5 seconds after it happens; the moonroof will fully close gradually. Make sure nothing is caught in the moonroof.

WARNING

● In an accident you could be thrown from the vehicle through an open moonroof.

Always use seat belts and child restraints.

● Do not allow anyone to stand up or extend any portion of their body out of the moonroof opening while the vehicle is in motion or while the moonroof is closing.

CAUTION

● Remove water drops, snow, ice or sand from the moonroof before opening.

● Do not place heavy objects on the moonroof or surrounding area.

Sunshade

Open and close the sunshade by sliding it forward or backward.

If the moonroof does not close

Have your NISSAN dealer check and repair the moonroof.

    Windows
    POWER WINDOWS WARNING ● Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows. Use the window lock switch to prevent ...

    Interior light
    1 The interior light can be turned ON regardless of door position. The light will go off after a period of time unless the ignition switch is placed in the ON position when any door is open ...

    Other materials:

    Tire labeling
    Example Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides the tire identification number (TIN) for safety standard certification. The ...

    Oil seal
    Removal and Installation of Valve Oil Seal REMOVAL 1. Remove camshaft. Refer to EM-41, "Removal and Installation". 2. Remove valve lifter. Refer to EM-41, "Removal and Installation". 3. Rotate crankshaft, and set piston whose oil seal is to removed to top dead center. ...

    B2617 Starter relay circuit
    Description Located in IPDM E/R, it runs the starter motor. The starter relay is turned ON by the BCM when the ignition switch is in START position. IPDM E/R transmits the starter relay ON signal to BCM via CAN communication. DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B2617 is display ...