Nissan Altima 2007-2012 Service Manual: Passenger side

Description

• BCM supplies power.

• Power window motor RH will be operated if power window and door lock/unlock switch RH is operated.

Component Function Check

Power Window And Door Lock/Unlock Switch RH

1. CHECK POWER WINDOW MOTOR RH FUNCTION

Does power window motor RH operate with power window and door lock/unlock switch RH operation? Is the inspection result normal? YES >> Power window and door lock/unlock switch RH power supply and ground circuit are OK.

NO >> Refer to PWC-200, "PASSENGER SIDE : Diagnosis Procedure".

 Diagnosis Procedure

Power Window And Door Lock/Unlock Switch RH Power Supply Circuit Check

1. CHECK POWER SUPPLY CIRCUIT

Check voltage between power window and door lock/unlock switch RH connector and ground.

Is the measurement value within the specification? YES >> GO TO 3

NO >> GO TO 2

2. CHECK HARNESS CONTINUITY

1. Turn ignition switch OFF.

2. Disconnect BCM and power window and door lock/unlock switch RH.

3. Check continuity between BCM connector (A) and power window and door lock/unlock switch RH connector (B).

4. Check continuity between BCM connector (A) and ground.

Is the inspection result normal? YES >> GO TO 4

NO >> Repair or replace harness.

3. CHECK GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect power window and door lock/unlock switch RH.

3. Check continuity between power window and door lock/unlock switch RH connector and ground.

Is the inspection result normal? YES >> Replace power window and door lock/unlock switch RH.

Refer to PWC-291, "Removal and Installation". After that, refer to PWC-201, "PASSENGER SIDE : Special Repair Requirement".

NO >> Repair or replace harness.

4. CHECK BCM OUTPUT SIGNAL

1. Connect BCM.

2. Turn ignition switch ON.

3. Check voltage between BCM connector and ground.

Is the measurement value within the specification? YES >> Replace power window and door lock/unlock switch RH.

Refer to PWC-291, "Removal and Installation". After that, refer to PWC-201, "PASSENGER SIDE : Special Repair Requirement".

NO >> Replace BCM. Refer to BCS-96, "Removal and Installation".

Special Repair Requirement

1. PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure.

Refer to PWC-190, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".

Is the inspection result normal? YES >> GO TO 2

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

2. CHECK ANTI-PINCH OPERATION

Check anti-pinch operation.

Refer to PWC-190, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".

Is the inspection result normal? YES >> Inspection end.

NO >> Refer to PWC-208, "PASSENGER SIDE : Component Function Check".

    Power window main switch
    Description • BCM supplies power. • It operates each power window motor via corresponding power window switch and makes window move up/ down when main power window and door lock/unlock swi ...

    Other materials:

    B2619 BCM
    Description BCM requests IPDM E/R to supply power to steering lock unit. After receiving the power, the steering lock unit transmits an ON signal to BCM. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1. Press the push-button ignition switc ...

    Front wiper and washer system
    System Diagram System Description OUTLINE The front wiper is controlled by each function of BCM and IPDM E/R. Control by BCM • Combination switch reading function • Front wiper control function Control by IPDM E/R • Front wiper control function • Relay control function FRONT WIP ...

    B2190, P1610 nats antenna amp
    Description Performs ID verification through BCM and keyfob when push-button ignition switch is pressed. Prohibits the release of steering lock or start of engine when an unregistered ID of keyfob is used. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMA ...