Nissan Altima (L32) 2007-2012 Service Manual: Driver side
Description
Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch.
Component Function Check
1. CHECK FRONT POWER WINDOW MOTOR LH CIRCUIT
Does front power window motor LH operate with the main power window and door lock/unlock switch? Is the inspection result normal? YES >> Front power window motor LH is OK.
NO >> Refer to PWC-114, "DRIVER SIDE : Diagnosis Procedure".
Diagnosis Procedure
Front Power Window Motor LH Circuit Check
1. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OUTPUT SIGNAL
1. Disconnect front power window motor LH.
2. Turn ignition switch ON.
3. Check voltage between front power window motor LH connector and ground.
Is the measurement value within the specification? YES >> GO TO 2
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-186, "Removal and Installation". After that, refer to PWC-115, "DRIVER SIDE : Special Repair Requirement".
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect main power window and door lock/unlock switch.
3. Check continuity between main power window and door lock/ unlock switch connector (A) and front power window motor LH connector (B).
4. Check continuity between main power window and door lock/unlock switch connector (A) and ground.
Is the inspection result normal? YES >> GO TO 3
NO >> Repair or replace harness.
3. CHECK FRONT POWER WINDOW MOTOR LH
Check front power window motor LH.
Refer to PWC-115, "DRIVER SIDE : Component Inspection".
Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> Replace front power window motor LH. Refer to GW-19, "Removal and Installation". After that, refer to PWC-115, "DRIVER SIDE : Special Repair Requirement".
Component Inspection
1.CHECK FRONT POWER WINDOW MOTOR LH
Does motor operate by connecting the battery voltage directly to power window motor?
Is the inspection result normal? YES >> Front power window motor LH is OK.
NO >> Replace front power window motor LH. Refer to GW-19, "Removal and Installation". After that, refer to PWC-115, "DRIVER SIDE : Special Repair Requirement".
Special Repair Requirement
1. PERFORM INITIALIZATION PROCEDURE
Perform initialization procedure.
Refer to PWC-95, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special Repair Requirement".
Is the inspection result normal? YES >> GO TO 2
NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
2. CHECK ANTI-PINCH OPERATION
Check anti-pinch operation.
Refer to PWC-95, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special Repair Requirement".
Is the inspection result normal? YES >> Inspection end.
NO >> Refer to PWC-114, "DRIVER SIDE : Component Function Check".
Passenger side
Description
Door glass moves UP/DOWN by receiving the signal from main power window and
door lock/unlock switch or
power window and door lock/unlock switch RH.
Component Function Check
1. CHECK ...
Other materials:
P0745 line pressure solenoid valve
Description
The pressure control solenoid valve A (line pressure solenoid valve)
regulates the oil pump discharge pressure
to suit the driving condition in response to a signal sent from the TCM.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
NOTE:
If “DTC CONFIRMATION PROCE ...
P2014 tumble control valve position
sensor
Description
Tumble control valve position sensor is built into the tumble control
valve actuator (2).
1 : Intake manifold adapter
3 : Tumble control valve
The sensor consists of a permanent magnet and Hall IC. It senses
the valve shaft movement and feeds the voltage signals to the ECM.
DTC ...
B2605 PNP switch
Description
BCM confirms the shift position with the following 4 signals.
• AT selector lever
• P/N position switch
• P position signal from IPDM E/R (CAN)
• P position signal from TCM (CAN)
DTC Logic
DTC DETECTION LOGIC
NOTE:
• If DTC B2605 is displayed with DTC U1000, first ...
