Nissan Altima 2007-2012 Service Manual:  B2190, P1610 nats antenna AMP

Description

Performs ID verification through BCM and Intelligent Key when push-button ignition switch is pressed.

Prohibits the release of steering lock or start of engine when an unregistered ID of Intelligent Key is used.

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION PROCEDURE

1. Insert Intelligent Key into the key slot.

2. Check “Self Diagnostic Result” with CONSULT-III.

Is DTC detected? YES >> Refer to SEC-263, "Diagnosis Procedure".

NO >> GO TO 2

2.PERFORM DTC CONFIRMATION PROCEDURE

1. Press the push-button ignition switch.

2. Check “Self Diagnostic Result” with CONSULT-III.

Is DTC detected? YES >> Refer to SEC-263, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

1. INSPECTION START

Check the case in which DTC is detected.

• Case1: It is detected when Intelligent Key is inserted into key slot.

• Case2: It is detected after Intelligent Key is inserted into key slot and push-button ignition switch is pressed.

In which case is DTC detected? Case1. >> GO TO 2

Case2. >> GO TO 4

2.CHECK KEY SLOT INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect key slot harness connector.

3. Check voltage between key slot harness connector and ground.

Is the inspection result normal? YES >> Replace key slot. Refer to SEC-409, "Removal and Installation".

NO >> GO TO 3

3.CHECK KEY SLOT CIRCUIT

1. Disconnect BCM harness connector.

2. Check continuity between key slot harness connector M40 (A) terminal 2 and BCM harness connector M19 (B) terminal 68.

3. Check continuity between key slot harness connector M40 (A) terminal 2 and ground.

Is the inspection result normal? YES >> GO TO 8

NO >> Repair harness or connector.

4.CHECK PUSH-IGNITION SWITCH OPERATION

Press push-button ignition switch and check if it turns ON.

Does ignition switch turn to ON? YES >> GO TO 5

NO >> GO TO 7

5.CHECK KEY SLOT COMMUNICATION SIGNAL

1. Turn ignition switch OFF.

2. Disconnect key slot harness connector.

3. Check voltage between key slot harness connector and ground.

Is the inspection result normal? YES >> Replace key slot. Refer to SEC-409, "Removal and Installation".

NO >> GO TO 6

6.CHECK KEY SLOT COMMUNICATION SIGNAL CIRCUIT

1. Disconnect BCM harness connector.

2. Check continuity between key slot harness connector M40 (A) terminal 3 and BCM harness connector M19 (B) terminal 69.

3. Check continuity between key slot harness connector M40 (A) terminal 3 and ground.

Is the inspection result normal? YES >> GO TO 8

NO >> Repair harness or connector.

7.CHECK KEY SLOT GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect key slot harness connector.

3. Check continuity between key slot harness connector and ground.

Is the inspection result normal? YES >> GO TO 8

NO >> Repair harness or connector.

8.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident".

>> Inspection End.

    B2110 PNP/clutch interlock switch
    Description IPDM E/R confirms the shift position with the following signals. • Park/neutral position (PNP) switch (CVT models) • Clutch inter lock switch (M/T models) • Shift position sign ...

    B2191, P1615 difference of key
    Description Performs ID verification through BCM and Intelligent Key when push-button ignition switch is pressed. Prohibits the release of steering lock or start of engine when an unregistered ...

    Other materials:

    B210F PNP/clutch interlock switch
    Description IPDM E/R confirms the shift position with the following signals. • Park/neutral position (PNP) switch (CVT models) • Clutch interlock switch (M/T models) • Shift position signal from BCM (CAN) DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B210F is displayed with DTC U100 ...

    Diagnosis and repair workflow
    Work Flow INTRODUCTION The TCM receives a signal from the vehicle speed sensor, PNP switch and provides shift control or lock-up control via CVT solenoid valves. The TCM also communicates with the ECM by means of a signal sent from sensing elements used with the OBD-related parts of the C ...

    P1225 TP Sensor
    Description Electric throttle control actuator consists of throttle control motor, throttle position sensor, etc. The throttle position sensor responds to the throttle valve movement. The throttle position sensor has two sensors. These sensors are a kind of potentiometers which transform the ...