Nissan Altima (L32) 2007-2012 Service Manual: B210E starter relay

11

Description

Located in IPDM E/R, it runs the starter motor. The starter relay is turned ON by the BCM when the ignition switch is in START position. IPDM E/R transmits the starter relay ON signal to BCM via CAN communication.

DTC Logic

DTC DETECTION LOGIC

NOTE: • If DTC B210E is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to SEC-36, "DTC Logic".

• If DTC B210E is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to SEC-37, "DTC Logic".

DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION PROCEDURE

1. Turn ignition switch ON under the following conditions and wait for at least 1 second.

- CVT selector lever is in the P or N position

- Do not depress the brake pedal

2. Check “Self diagnostic result” with CONSULT-III.

Is DTC detected? YES >> Refer to SEC-51, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

1.INSPECTION START

Check which type of transmission the vehicle is equipped with.

Which type of transmission CVT >> GO TO 2

M/T >> GO TO 3

2.CHECK STARTER RELAY OUTPUT SIGNAL/CVT MODELS

1. Turn ignition switch OFF.

2. Disconnect BCM harness connector.

3. Check voltage between BCM harness connector and ground.

Is the inspection result normal? YES >> GO TO 5

NO >> GO TO 4

3.CHECK STARTER RELAY OUTPUT SIGNAL / M/T MODELS

1. Turn ignition switch OFF.

2. Disconnect BCM harness connector.

3. Check voltage between BCM harness connector and ground.

Is the inspection result normal? YES >> GO TO 5

NO >> GO TO 4

4.CHECK STARTER RELAY OUTPUT SIGNAL CIRCUIT

1. Disconnect IPDM E/R harness connector.

2. Check continuity between IPDM E/R harness connector and BCM harness connector.

3. Check continuity between BCM harness connector and ground.

Is the inspection result normal? YES >> Replace IPDM E/R. Refer to PCS-48, "Removal and Installation".

NO >> Repair harness connector.

5.CHECK STARTER RELAY POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R harness connector.

3. Check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal? YES >> Replace IPDM E/R. Refer to PCS-48, "Removal and Installation".

NO >> Check harness for open or short between IPDM E/R and battery.

    B210D starter relay
    Description Located in IPDM E/R, it runs the starter motor. The starter relay is turned ON by the BCM when the ignition switch is in START position. IPDM E/R transmits the starter relay ON signal ...

    B210F PNP/clutch interlock switch
    Description IPDM E/R confirms the shift position with the following signals. • Park/neutral position (PNP) switch (CVT models) • Clutch interlock switch (M/T models) • Shift position signa ...

    Other materials:

    P1564 ASCD Steering switch
    Description ASCD steering switch has variant values of electrical resistance for each button. ECM reads voltage variation of switch, and determines which button is operated. Refer to EC-1090, "System Diagram" for the ASCD function. DTC Logic DTC DETECTION LOGIC NOTE: If DTC P156 ...

    Idle speed
    Description This describes how to check the idle speed. For the actual procedure, follow the instructions in “BASIC INSPECTION”. Special Repair Requirement 1.CHECK IDLE SPEED Check idle speed in “DATA MONITOR” mode with CONSULT-III. Check idle speed with Service $01 of GST. > ...

    P0128 Thermostat function
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0128 is displayed with DTC P0300, P0301, P0302, P0303 or P0304, first perform the trouble diagnosis for DTC P0300, P0301, P0302, P0303, P0304. Refer to EC-776, "DTC Logic". Engine coolant temperature has not risen enough to open the t ...