Nissan Altima 2007-2012 Service Manual: B261a push-button ignition switch

Description

IPDM E/R transmits the push-button ignition switch status via CAN communication to BCM. BCM receives push-button ignition switch status by hardwire input. BCM compares the 2 signals for mismatch.

DTC Logic

DTC DETECTION LOGIC

NOTE: • If DTC B261A is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to SEC-36, "DTC Logic".

• If DTC B261A is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to SEC-37, "DTC Logic".

DTC CONFIRMATION PROCEDURE

1.PERFORM DTC CONFIRMATION PROCEDURE

1. Press the push-button ignition switch under the following conditions and wait for at least 1 second.

- CVT selector lever is in the P position

- Do not depress brake pedal.

2. Check “Self diagnostic result” with CONSULT-III.

Is DTC detected? YES >> Refer to SEC-108, "Diagnosis Procedure".

NO >> Inspection End.

Diagnosis Procedure

1.CHECK PUSH-BUTTON IGNITION SWITCH OUTPUT SIGNAL 1

1. Turn ignition switch OFF.

2. Disconnect push-button ignition switch harness connector and IPDM E/R harness connector.

3. Check voltage between push-button ignition switch harness connector and ground.

Is the inspection result normal? YES >> GO TO 4

NO >> GO TO 2

2.CHECK PUSH-BUTTON IGNITION SWITCH CIRCUIT

1. Disconnect BCM harness connector.

2. Check continuity between push-button ignition switch harness connector M38 (A) terminal 4 and BCM harness connector M19 (B) terminal 77.

3. Check continuity between push-button ignition switch harness connector M38 (A) terminal 4 and ground.

Is the inspection result normal? YES >> GO TO 3

NO >> Repair harness or connector.

3.CHECK PUSH-BUTTON IGNITION SWITCH

1. Disconnect IPDM E/R harness connector.

2. Check continuity between push-button ignition switch harness connector M38 (A) terminal 4 and IPDM E/R harness connector E18 (B) terminal 28.

3. Check continuity between push-button ignition switch harness connector and ground.

Is the inspection result normal? YES >> GO TO 4

NO >> Repair harness or connector.

4.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident".

>> Inspection End.

    B2619 BCM
    Description BCM requests IPDM E/R to supply power to steering lock unit. After receiving the power, the steering lock unit transmits an ON signal to BCM. DTC Logic DTC DETECTION LOGIC DTC C ...

    B26e1 no reception of engine status signal
    Description BCM receives the engine status signal from ECM via CAN communication. DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B26E1 is displayed with DTC U1000, first perform the trouble diag ...

    Other materials:

    BCM branch line circuit
    Diagnosis Procedure INSPECTION PROCEDURE 1.CHECK CONNECTOR 1. Turn the ignition switch OFF. 2. Disconnect the battery cable from the negative terminal. 3. Check the terminals and connectors of the BCM for damage, bend and loose connection (unit side and connector side). Is the inspec ...

    B2607 steering lock relay
    Description BCM requests to IPDM E/R to supply power to electronic steering column lock. IPDM E/R sends status of electronic steering column lock back to BCM. DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B2607 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U100 ...

    On-vehicle repair
    BATTERY Removal and Installation REMOVAL 1. Remove air duct (front). Refer to EM-25, "Removal and Installation" QR25DE models, EM-129, "Removal and Installation" VQ35DE models. 2. Loosen battery terminal nuts, and disconnect both battery terminals. CAUTION: When disc ...