Nissan Altima 2007-2012 Service Manual: Body side trim

Exploded View

1. Front pillar finisher

2. Dash side lower finisher

3. Front kicking plate

4. Front sill cover

5. Center pillar lower finisher

6. Rear sill cover

7. Rear kicking plate

8. Rear body side welt

9. Rear pillar finisher

10. Screw cover

11. Center pillar upper finisher

12. Front seat belt adjuster cover

13. Front body side welt

A. Screw

Removal and Installation

CAUTION: • Wrap the tip of flat-bladed screwdriver with a cloth when removing metal clips from garnishes.

• When removing or installing body side welts, do not allow butyl seal to come in contact with pillar finishers.

REMOVAL

FRONT PILLAR FINISHER

1. Remove front body side welt.

CAUTION: Insert a suitable clip removing tool wrapped with a shop cloth inserted into the part shown by the arrow (between the clip and the body side panel), then release the clip. 2. Release the clips, then remove front pillar finisher.

DASH SIDE LOWER FINISHER

1. Remove front kicking plate.

2. Release the clips, then remove dash side lower finisher.

FRONT KICKING PLATE

Release the clip and pawls, then remove front kicking plate.

FRONT BODY SIDE WELT

1. Remove front kicking plate.

2. Release welt from the body opening, then remove front body side welt.

CENTER PILLAR LOWER FINISHER

1. Remove front and rear body side welt.

2. Remove front and rear kicking plate.

3. Release the clips and pawls, then remove center pillar lower finisher.

CENTER PILLAR UPPER FINISHER

1. Remove screw cover, then remove the screw.

2. Remove front seat belt adjuster cover and shoulder anchor bolt. Refer to SB-7, "Exploded View".

3. Remove center pillar lower finisher.

4. Release the clips, then remove center pillar upper finisher.

REAR KICKING PLATE

Release the clip and pawl, then remove rear kicking plate.

REAR BODY SIDE WELT

1. Remove rear body side welt.

2. Remove screw cover, then remove the screw.

3. Release the clips, then remove rear pillar finisher.

SILL PLATE COVER (FRONT/REAR)

Release the pawls, then remove the sill plate cover.

INSTALLATION

Installation is in the reverse order of removal. CAUTION: Make sure that clips are fully aligned with panel holes on body when installing, then press them in completely.

    Door finisher
    Exploded View 1. Mirror cover 2. Front door finisher 3. Step lamp lens 4. Rear door finisher 5. Step lamp/reflector lens (if equipped) 6. Arm rest finisher 7. Rear door power window switch f ...

    Rear parcel shelf finisher
    Exploded View 1. Seatback release escutcheon 2. Seatback release cover 3. Child anchor cover 4. Seatback latch cover 5. Rear parcel shelf finisher 6. High mounted stop lamp (if equipped) A. ...

    Other materials:

    Phone settings
    To access the phone settings: 1. Press the [ ] button. 2. Select the “Settings” key. 3. Select the “Phone & Bluetooth” key. 4. Select the “Phone Settings” key and adjust the following settings as desired: ● Sort Phonebook By: Select “First Name” or “Last Name” to ...

    NVIS (Nissan vehicle immobilizer system-nats)
    System Diagram System Description INPUT/OUTPUT SIGNAL CHART SYSTEM DESCRIPTION • The NVIS (NATS) is an anti-theft system by registering an Intelligent Key ID in to the vehicle and prevents the engine being started by an unregistered Intelligent Key. It has a higher protection agains ...

    Electrical load signal
    Description The electrical load signal (Headlamp switch signal, rear window defogger switch signal, etc.) is transferred via the CAN communication. Component Function Check 1.CHECK REAR WINDOW DEFOGGER SWITCH FUNCTION 1. Turn ignition switch ON. 2. Connect CONSULT-III and select “DATA MO ...