Nissan Altima 2007-2012 Service Manual: Door key cylinder switch

Description

Power window main switch detects condition of the door key cylinder and transmits to BCM as the LOCK or UNLOCK signals.

Component Function Check

1. CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL

Check (“KEY CYL LK-SW”, “KEY CYL UN-SW”) in “DATA MONITOR” mode for “POWER DOOR LOCK SYSTEM” with CONSULT-III. Refer to BCS-19, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)".

Is the inspection result normal? YES >> Key cylinder switch is OK.

NO >> Refer to PWC-328, "Diagnosis Procedure".

Diagnosis Procedure

1. CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL

1. Turn ignition switch ON.

2. Check voltage between main power window and door lock/ unlock switch connector and ground.

Is the measurement value within the specification? YES >> Replace main power window and door lock/unlock switch. After that, refer to PWC-307, "POWER WINDOW MAIN SWITCH : Special Repair Requirement".

NO >> GO TO 2

2. CHECK DOOR KEY CYLINDER SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect main power window and door lock/unlock switch and front door lock assembly LH (key cylinder switch).

3. Check continuity between main power window and door lock/ unlock switch connector (A) and front door lock assembly LH (key cylinder switch) connector (B).

4. Check continuity between main power window and door lock/unlock switch connector (A) and ground.

Is the inspection result normal? YES >> GO TO 3

NO >> Repair or replace harness.

3. CHECK DOOR KEY CYLINDER SWITCH GROUND CIRCUIT

Check continuity between front door lock assembly LH (key cylinder switch) connector and ground.

Is the inspection result normal? YES >> GO TO 4

NO >> Repair or replace harness.

4. CHECK DOOR KEY CYLINDER SWITCH

Check door key cylinder switch.

Refer to PWC-329, "Component Inspection".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Replace front door lock assembly LH (door key cylinder switch). After that, refer to PWC-330, "Special Repair Requirement".

Component Inspection

1. CHECK DOOR KEY CYLINDER SWITCH

Check front door lock assembly LH (key cylinder switch).

Is the inspection result normal? YES >> Key cylinder switch is OK.

NO >> Replace front door lock assembly LH (key cylinder switch). After that, refer to PWC-330, "Special Repair Requirement".

Special Repair Requirement

1. PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure.

Refer to PWC-295, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special Repair Requirement".

Is the inspection result normal? YES >> Inspection End.

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

    Door switch
    Description Detects door open/close condition and transmits the signal to BCM. Component Function Check 1. CHECK FRONT DOOR SWITCH INPUT SIGNAL Check (“DOOR SW-DR” and “DOOR SW-AS”) in ...

    Other materials:

    Spark plug
    Removal and Installation 1. Ignition coil 2. Spark plug 3. Rocker cover REMOVAL 1. Remove the ignition coil. Refer to EM-35, "Removal and Installation". 2. Remove the spark plug with a suitable spark plug wrench. INSPECTION AFTER REMOVAL • Do not use a wire brush for clean ...

    Precaution
    Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the dr ...

    Precautions on supplemental restraint system
    This Supplemental Restraint System (SRS) section contains important information concerning the following systems: ● Driver and passenger supplemental frontimpact air bag (NISSAN Advanced Air Bag System) ● Front seat-mounted side-impact supplemental air bag ● Roof-mounted cu ...