Nissan Altima 2007-2012 Service Manual: Driver side

 Description

Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch.

Component Function Check

1. CHECK POWER WINDOW MOTOR LH CIRCUIT

Does power window motor LH operate with the main power window and door lock/unlock switch? Is the inspection result normal? YES >> Power window motor LH is OK.

NO >> Refer to PWC-25, "DRIVER SIDE : Diagnosis Procedure".

Diagnosis Procedure

Power Window Motor LH Circuit Check

1. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OUTPUT SIGNAL

1. Disconnect power window motor LH.

2. Turn ignition switch ON.

3. Check voltage between power window motor LH connector and ground.

Is the measurement value within the specification? YES >> GO TO 2

NO >> Replace main power window and door lock/unlock switch. Refer to PWC-91, "Removal and Installation".

After that, refer to PWC-12, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".

2. CHECK HARNESS CONTINUITY

1. Turn ignition switch OFF.

2. Disconnect main power window and door lock/unlock switch.

3. Check continuity between main power window and door lock/ unlock switch connector (A) and power window motor LH connector (B).

4. Check continuity between main power window and door lock/unlock switch connector (A) and ground.

Is the inspection result normal? YES >> GO TO 3

NO >> Repair or replace harness.

3. CHECK POWER WINDOW MOTOR LH

Check power window motor LH.

Refer to PWC-203, "DRIVER SIDE : Component Inspection".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Replace power window motor LH. Refer to GW-19, "Removal and Installation". After that, refer to PWC-12, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".

Component Inspection

COMPONENT INSPECTION

1. CHECK POWER WINDOW MOTOR LH

Does motor operate by connecting the battery voltage directly to power window motor?

Is the inspection result normal? YES >> Power window motor LH is OK.

NO >> Replace power window motor LH. Refer to GW-19, "Removal and Installation". After that, refer to PWC-12, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".

 Special Repair Requirement

1. PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure.

Refer to PWC-12, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".

Is the inspection result normal? YES >> GO TO 2

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

2. CHECK ANTI-PINCH OPERATION

Check anti-pinch operation.

Refer to PWC-12, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".

Is the inspection result normal? YES >> Inspection End.

NO >> Refer to PWC-29, "DRIVER SIDE : Component Function Check".

    Passenger side
     Description Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch or power window and door lock/unlock switch RH. Component Function Check 1. ...

    Other materials:

    Diagnosis and repair workflow
    Work Flow OVERALL SEQUENCE DETAILED FLOW 1.GET INFORMATION FOR SYMPTOM Get the detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurred). >> GO TO 2 2.CHECK DTC WITH BCM AND IPDM E/R 1. Check “Self Diagn ...

    STRG branch line circuit
    Diagnosis Procedure INSPECTION PROCEDURE 1.CHECK CONNECTOR 1. Turn the ignition switch OFF. 2. Disconnect the battery cable from the negative terminal. 3. Check the terminals and connectors of the steering angle sensor for damage, bend and loose connection (unit side and connector side). ...

    Power supply and ground circuit
    Diagnosis Procedure 1. CHECK FUSE AND FUSIBLE LINK Check if the following BCM fuse or fusible link are blown. Is the fuse or fusible link blown? YES >> Replace the blown fuse or fusible link after repairing the affected circuit. NO >> GO TO 2 2. CHECK POWER SUPPLY CIRCUIT 1. ...