Nissan Altima 2007-2012 Service Manual: Driver side

 Description

Detects condition of the power window motor LH operation and transmits to main power window and door lock/unlock switch as pulse signal.

Component Function Check

1. CHECK ENCODER OPERATION

Does door glass LH perform AUTO open/close operation normally when operating main power window and door lock/unlock switch? Is the inspection result normal? YES >> Encoder operation is OK.

NO >> Refer to PWC-206, "DRIVER SIDE : Diagnosis Procedure".

Diagnosis Procedure

Encoder Circuit Check

1. CHECK ENCODER OPERATION

1. Turn ignition switch ON.

2. Check signal between main power window and door lock/unlock switch connector and ground with oscilloscope.

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> GO TO 2

2. CHECK POWER WINDOW MOTOR LH POWER SUPPLY

1. Turn ignition switch ON.

2. Check voltage between power window motor LH connector and ground.

Is the measurement value within the specification? YES >> GO TO 4

NO >> GO TO 3

3. CHECK HARNESS CONTINUITY 1

1. Turn ignition switch OFF.

2. Disconnect main power window and door lock/unlock switch and power window motor LH.

3. Check continuity between main power window and door lock/ unlock switch connector (A) and power window motor LH connector (B).

4. Check continuity between main power window and door lock/unlock switch connector (A) and ground.

Is the inspection result normal? YES >> Replace main power window and door lock/unlock switch. Refer to PWC-291, "Removal and Installation". After that, refer to PWC-199, "POWER WINDOW MAIN SWITCH : Special Repair Requirement".

NO >> Repair or replace harness.

4. CHECK GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect power window motor LH.

3. Check continuity between power window motor LH connector and ground.

Is the inspection result normal? YES >> GO TO 6

NO >> GO TO 5

5. CHECK HARNESS CONTINUITY 2

1. Disconnect main power window and door lock/unlock switch.

2. Check continuity between main power window and door lock/ unlock switch connector (A) and power window motor LH connector (B).

Is the inspection result normal? YES >> Replace main power window and door lock/unlock switch. Refer to PWC-291, "Removal and Installation". After that, refer to PWC-199, "POWER WINDOW MAIN SWITCH : Special Repair Requirement".

NO >> Repair or replace harness.

6. CHECK HARNESS CONTINUITY 3

1. Disconnect main power window and door lock/unlock switch.

2. Check continuity between main power window and door lock/ unlock switch connector (A) and power window motor LH connector (B).

3. Check continuity between main power window and door lock/ unlock switch connector (A) and ground.

Is the inspection result normal? YES >> Replace power window motor LH. Refer to GW-19, "Removal and Installation". After that, refer to PWC-203, "DRIVER SIDE : Special Repair Requirement".

NO >> Repair or replace harness.

    Encoder
    ...

    Passenger side
     Description Detects condition of the power window motor RH operation and transmits to power window and door lock/ unlock switch RH as pulse signal. Component Function Check 1. CHECK ENCOD ...

    Other materials:

    Rear bumper
    Removal and Installation 1. Rear bumper side brackets 2. Rear bumper supports 3. Rear bumper reinforcement 4. Rear energy absorbing foam 5. Rear bumper fascia A. C205 push pin REMOVAL 1. Remove the LH and RH rear combination lamps. Refer to EXL-260, "Removal and Installation" ...

    Rear speaker
    Removal and Installation - Coupe REMOVAL 1. Remove the trunk front finisher. Refer to INT-23, "Removal and Installation". 2. Remove the rear speaker screws (A), then disconnect the rear speaker connector (B) and remove the rear speaker (1). INSTALLATION Installation is in the ...

    NISSAN Intelligent Key® battery discharge
    If the battery of the NISSAN Intelligent Key® is discharged, or environmental conditions interfere with the Intelligent Key operation, start the engine according to the following procedure: 1. Place the shift lever in the P (Park) position. 2. Firmly apply the foot brake. 3. Touch the ignit ...