Nissan Altima 2007-2012 Service Manual: Electronic controlled engine mount

System Diagram

System Description

INPUT/OUTPUT SIGNAL CHART

*: This signal is sent to the ECM via the CAN communication line.

SYSTEM DESCRIPTION

The ECM controls the engine mount operation corresponding to the engine speed. The control system has a 2-step control [Soft/Hard]

ELECTRONIC CONTROLLED ENGINE MOUNT LINE DRAWING

1. Power valve actuator 1

2. VIAS control solenoid valve 1

3. VIAS control solenoid valve 2

4. Power valve actuator 2

5. Intake manifold collector

1. Electronic controlled engine mount control solenoid valve

2. Front electronic controlled engine mount

3. Rear electronic controlled engine mount

NOTE: Do not use soapy water or any type of solvent while installing vacuum hose.

Component Parts Location

1. Power valve actuator 1

2. Intake valve timing control solenoid valve (bank 1)

3. Power steering pressure sensor

4. Intake valve timing control solenoid valve (bank 2)

5. VIAS control solenoid valves 1 and 2

6. Fuel injector (bank 2)

7. Ignition coil (with power transistor) and spark plug (bank 2)

8. Crankshaft position sensor (POS)

9. Engine coolant temperature sensor

10. Camshaft position sensor (PHASE) (bank 2)

11. ECM

12. Refrigerant pressure sensor

13. Battery current sensor

14. PNP switch

15. Condenser-2

16. Mass air flow sensor (with intake air temperature sensor)

17. EVAP service port

18. Camshaft position sensor (PHASE) (bank 1)

19. Electric throttle control actuator

20. Power valve actuator 2

21. EVAP canister purge volume control solenoid valve

22. Ignition coil (with power transistor) and spark plug (bank 1)

23. Knock sensor

1. Mas air flow sensor (with intake air temperature sensor)

2. Air cleaner case

3. Engine coolant temperature sensor

4. EVAP canister purge volume control solenoid valve

5. Power valve actuator 1

6. VIAS control solenoid valve 1

7. VIAS control solenoid valve 2

8. Power valve actuator 2

9. Power steering pressure sensor

10. Tie rod (RH)

11. Power valve actuator 2

12. Camshaft position sensor (PHASE) (bank 1)

13. Camshaft position sensor (PHASE) (bank 2)

1. A/F sensor 1 (bank 1)

2. A/F sensor 1 (bank 2)

3. HO2S2 (bank 1) harness connector

4. HO2S2 (bank 2) harness connector (CVT models)

5. Front engine mount

6. HO2S2 (bank 2) harness connector (M/T models)

7. Crankshaft position sensor (POS) (M/T models)

8. Crankshaft position sensor (POS) (CVT models)

1. Electronic controlled engine mount control solenoid valve

2. EVAP control system pressure sensor

3. EVAP canister vent control valve

4. EVAP canister

5. Injector harness connector

6. Intake valve timing control solenoid valve (bank 1)

7. Intake valve timing control solenoid valve (bank 2)

1. Knock sensor (bank 2)

2. Knock sensor (bank 1)

3. PNP switch (CVT models)

4. PNP switch (M/T models)

5. Battery

6. IPDM E/R

7. ECM

8. Refrigerant pressure sensor (shown with front grill removed)

9. Accelerator pedal

1. ASCD brake switch

2. Stop lamp switch

3. Brake pedal

4. ASCD steering switch

5. ASCD clutch switch (M/T models)

6. Clutch pedal

Component Description

    Cooling fan control
    System Diagram System Description INPUT/OUTPUT SIGNAL CHART *1: The ECM determines the start signal status by the signals of engine speed and battery voltage. *2: This signal is sent to EC ...

    Evaporative emission system
    System Diagram System Description INPUT/OUTPUT SIGNAL CHART *1: ECM determines the start signal status by the signals of engine speed and battery voltage. *2: This signal is sent to the ...

    Other materials:

    Diagnosis and repair workflow
    Work Flow OVERALL SEQUENCE • Reference 1··· Refer to AV-289, "CONSULT - III Function (MULTI AV)". • Reference 2··· Refer to AV-424, "Symptom Table". DETAILED FLOW 1.CHECK SYMPTOM Check the malfunction symptoms by performing the following items. • Intervie ...

    Intake valve timing control
    System Diagram System Description INPUT/OUTPUT SIGNAL CHART *: This signal is sent to the ECM through CAN communication line SYSTEM DESCRIPTION This mechanism hydraulically controls cam phases continuously with the fixed operating angle of the intake valve. The ECM receives signals s ...

    Basic inspection
    DIAGNOSIS AND REPAIR WORKFLOW Work Flow OVERALL SEQUENCE DETAILED FLOW 1. GET INFORMATION FOR SYMPTOM Get the detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurred). >> GO TO 2 2. CHECK DTC 1. Check DT ...