Nissan Altima 2007-2012 Service Manual: Exhaust manifold and three way catalyst

Removal and Installation

1. Exhaust manifold cover (upper)

2. Exhaust manifold stay

3. Manifold yoke (type B)

4. Manifold yoke (type A)

5. Exhaust manifold cover (lower)

6.. Exhaust manifold and three way catalyst assembly

7.  Exhaust manifold gasket

8. Air fuel ratio (A/F) sensor 1

A. To cylinder head

REMOVAL

1. Remove the engine undercover using power tools.

2. Disconnect the electrical connector of air fuel ratio (A/F) sensor 1, and unhook the harness from the bracket and middle clamp on the cover.

3. Remove the air fuel ratio (A/F) sensor 1 using Tools.

Tool numbers : — (J-44626) : KV10117100 (J-36471-A)

CAUTION: • Be careful not to damage air fuel ratio (A/F) sensor.

• Discard any air fuel ratio (A/F) sensor which has been dropped from a height of more than 0.5 m (19.7 in) onto a hard surface such as a concrete floor; replace with a new one.

4. Remove the exhaust manifold cover (lower).

5. Remove the exhaust front tube. Refer to EX-6, "Removal and Installation".

6. Remove the exhaust manifold cover (upper).

7. Loosen the nuts in the reverse order as shown, on the exhaust manifold and three way catalyst assembly.

8. Remove the exhaust manifold and three way catalyst assembly and gasket. Discard the gasket.

INSPECTION AFTER REMOVAL

Surface Distortion

• Use a reliable straightedge and feeler gauge to check the flatness of exhaust manifold fitting surface.

Limit : 0.3 mm (0.012 in)

INSTALLATION

Installation is in the reverse order of removal.

Tightening Exhaust Manifold Nuts

• Tighten the nuts to specification in the numerical order shown, on the exhaust manifold and three way catalyst assembly.

Installation of Air Fuel Ratio (A/F) Sensor 1

Clean the air fuel ratio (A/F) sensor 1 threads with the Tool, then apply the anti-seize lubricant to the threads before installing the air fuel ratio (A/F) sensor 1.

Tool number : J-43897 - 18

: J-43897 - 12

CAUTION: Do not over-tighten the air fuel ratio (A/F) sensor 1. Doing so may cause damage to the air fuel ratio (A/ F) sensor 1, resulting in a malfunction and the MIL coming on.

    Intake manifold
    Removal and Installation 1. Intake manifold 2. Rubber seal 3. Intake manifold adapter 4. Gasket 5. Electric throttle control actuator 6. Rubber seal 7. PCV hose 8. EVAP canister purge volume ...

    Oil pan and oil strainer
    Removal and Installation 1. Oil level gauge guide 2. Oil pan, upper 3. Cylinder block 4. Oil filter 5. Oil strainer 6. Drain plug 7. Oil pan, lower 8. Rear plate cover 9. O-ring A. To oil ...

    Other materials:

    B terminal circuit
    Description The “B” terminal is constantly supplied with battery power. Diagnosis Procedure CAUTION: Perform diagnosis under the condition that the engine cannot start by the following procedure. 1. Remove fuel pump fuse. 2. Crank or start the engine (where possible) until the fuel p ...

    Transverse link
    Removal and Installation REMOVAL 1. Remove wheel and tire. Refer to WT-66, "Adjustment". 2. Remove steering knuckle from transverse link. Refer to FSU-12, "Exploded View". 3. Remove mounting nuts and washers on lower portion of stabilizer connecting rod. 4. Slightl ...

    Cleaning interior
    Occasionally remove loose dust from the interior trim, plastic parts and seats using a vacuum cleaner or soft bristled brush. Wipe the vinyl and leather surfaces with a clean, soft cloth dampened in mild soap solution, then wipe clean with a dry, soft cloth. Regular care and cleaning is requ ...