Nissan Altima 2007-2012 Service Manual: Front seat

Exploded View

DRIVER'S SEAT

1. Headrest

2. Headrest holder (locked)

3. Headrest holder (free)

4. Seatback board

5. Seatback assembly

6. Slide cover

7. Seat belt buckle

8. Seat harness

9. Seat cushion heater unit

10. Seat cushion

11. Seat trim

12. Front leg covers

13. Seat cushion frame

14. Manual seat lifter lever finisher

15. Manual seat recliner handle

16. Manual seat lifter lever

17. Manual seat outer finisher

18. Seat slide switch

19. Seat reclining switch

20. Power seat outer finisher

21. Seat switch assembly

22. LH seat bracket

23. Front seat finisher

24. Cushion bracket

25. Inner seat cover

26. Seat frame assembly

27. Cushion finishers

28. Rear leg covers

PASSENGER'S SEAT

1. Headrest

2. Headrest holder (locked)

3. Headrest holder (free)

4. Seatback board

5. Seatback assembly

6. Seat cushion assembly

7. Bushing

8. Seat cushion frame assembly

9. Front leg covers

10. Cushion bracket

11. Seat frame assembly

12. Seat harness

13. Seat belt buckle

14. Inner finisher

15. Outer finisher

16. Seat cushion supporter

17. Recliner mechanism

18. Finisher

19. Cushion finishers

20. Rear leg covers

Removal and Installation

REMOVAL

CAUTION: • Before removing the front seat, turn the ignition switch off, disconnect both battery terminals and wait and least 3 minutes.

• When checking the power seat circuit for continuity using a circuit tester, do not confuse its connector with the side air bag module connector. Such an error may cause the air bag to deploy.

• Do not drop, tilt, or bump the side air bag module while installing the seat. Always handle it with care.

• After front side air bag module inflates, front seatback assembly must be replaced.

• Always replace passenger seat cushion as an assembly with Occupant Classification System.

• When removing or installing the seat trim, handle it carefully to keep dirt out and avoid damage.

• When removing and installing, use shop cloths to protect the parts from damage where they may interfere with other parts.

1. Slide the seat until the four seat bolts are visible and a tool can be inserted.

2. Disconnect the negative and positive battery terminals and wait at least 3 minutes.

3. Disconnect the harness connector for the side air bag module.

4. Disconnect the power seat harness connector and vehicle harness clip from the vehicle.

5. Remove the seat leg covers.

6. Remove the four seat bolts.

INSTALLATION

Installation is in the reverse order of removal.

• When installing the LH front seats tighten the bolts as shown.

• When installing the RH front seats tighten the bolts as shown.

    Rear seat
    Exploded View BENCH SEAT 1. Rear seat side bolster assembly LH 2. Rear seatback latch mount 3. Rear seat side bolster assembly RH 4. Rear seatback latch 5. Rear seatback trim panel 6. Seat b ...

    Other materials:

    B2602 shift position
    Description BCM confirms the shift position with the following 2 signals. • CVT selector lever • Speed signal from meter DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B2602 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to SEC-433, "DTC ...

    Door finisher
    Exploded View 1. Power window switch finisher 2. Front door finisher 3. Step lamp 4. Armrest finisher 5. Inside release handle escutcheon 6. Inside release handle Removal and Installation Removal 1. Release the pawls at the rear edge and remove inside release handle escutcheon, then ...

    Oil filter
    Removal and Installation REMOVAL 1. Remove the engine undercover. 2. Remove the oil filter using Tool (A) as shown. WARNING: • Be careful not to get burned, the engine and engine oil may be hot. CAUTION: • When removing, prepare a shop cloth to absorb any oil leakage or spillag ...