Nissan Altima 2007-2012 Service Manual: Front seat belt

Exploded View

1. D-ring anchor

2. Adjuster cover

3. Outer anchor bolt cover

4. Seat belt pre-tensioner connector

5. Seat belt retractor

6. Seat belt adjuster

A. D-ring anchor bolt

B. Outer anchor bolt

C. Retractor screw

D. Retractor anchor bolt

E. Bolt

1. Seat belt retractor

2. Seat belt pre-tensioner connector

3. Anchor bolt cover

4. D-ring anchor bolt cover

5. D-ring assembly

A. Retractor screw

B. Retractor anchor bolt

C. Anchor bolt

D. D-ring anchor bolt

Removal and Installation

REMOVAL OF SEAT BELT RETRACTOR - COUPE

CAUTION: Before servicing SRS, turn the ignition switch off, disconnect both negative and positive battery terminals, then wait at least three minutes.

1. Disconnect both negative and positive battery terminals, then wait at least three minutes.

2. Remove the rear seat cushion and seat back. Refer to SE-25, "Removal and Installation".

3. Release the pawl and remove anchor bolt cover, then remove lower anchor bolt.

4. Release the D-ring anchor bolt cover, then remove D-ring anchor bolt from center pillar.

5. Remove upper pillar finisher and rear lower finisher. Refer to INT-15, "Removal and Installation".

6. Disconnect seat belt pre-tensioner connector (1).

CAUTION: • For installing/removing seat belt pre-tensioner connector, insert a thin screwdriver wrapped with tape into the notch; lift locking tab then remove connector.

• Install connector with lock raised, then push locking tab into connector.

7. Remove seat belt retractor screw (A) and retractor anchor bolt (B), then remove seat belt retractor (2) from center pillar.

INSTALLATION OF SEAT BELT RETRACTOR - COUPE

Installation is in the reverse order of removal.

• Always perform an inspection after repair to be sure the system is functioning within specifications. Refer to SB-4, "Inspection".

REMOVAL OF SEAT BELT RETRACTOR - SEDAN

CAUTION: Before servicing SRS, turn the ignition switch off, disconnect both negative and positive battery terminals, then wait at least three minutes.

1. Disconnect both negative and positive battery terminals, then wait at least three minutes.

2. Release the pawl, then remove outer anchor bolt cover and outer anchor bolt.

3. Remove center pillar lower and upper finishers. Refer to INT-36, "Removal and Installation".

4. Remove D-ring anchor bolt from seat belt adjuster.

5. Remove seat belt retractor.

• Disconnect the seat belt pre-tensioner connector.

CAUTION: • For installing/removing seat belt pre-tensioner connector, insert a thin screwdriver wrapped with tape into the notch; lift locking tab then remove connector.

• Install connector with lock raised, then push locking tab into connector.

• Remove screw and retractor anchor bolt, then remove seat belt retractor from center pillar.

6. Remove bolts, then remove seat belt adjuster from center pillar.

INSTALLATION OF SEAT BELT RETRACTOR- SEDAN

Installation is in the reverse order of removal.

• Always perform an inspection after repair to be sure the system is functioning within specifications. Refer to SB-4, "Inspection".

REMOVAL OF SEAT BELT BUCKLE

CAUTION: Before servicing SRS, turn the ignition switch off, disconnect both negative and positive battery terminals, then wait at least three minutes.

1. Disconnect the negative and positive battery terminals, then wait at least three minutes.

2. Remove the front seat from the vehicle. Refer to SE-23, "Removal and Installation".

3. Remove anchor nut (A) from the seat belt buckle (1).

4. Disconnect the seat belt buckle harness connector (2), release the harness clip(s), then remove the seat belt buckle (1).

INSTALLATION OF SEAT BELT BUCKLE

Installation is in the reverse order of removal.

• Always perform an inspection after repair to be sure the system is functioning within specifications. Refer to SB-4, "Inspection".

    Rear seat belt
    Exploded View 1. Seat belt retractor RH 2. Seat belt buckle RH 3. Seat belt buckle center 4. Seat belt buckle LH 5. Seat belt retractor center 6. Seat belt retractor LH A. Retractor anchor bo ...

    Other materials:

    P0102, P0103 maf sensor
    Description The mass air flow sensor (1) is placed in the stream of intake air. It measures the intake flow rate by measuring a part of the entire intake flow. The mass air flow sensor controls the temperature of the hot wire to a certain amount. The heat generated by the hot wire is reduced a ...

    Lan system circuit
    Description SYMPTOM: Mode door motor, intake door motor and/or air mix door motor does not operate normally. Diagnosis Procedure DIAGNOSIS PROCEDURE FOR LAN CIRCUIT 1.CHECK POWER SUPPLY FOR DOOR MOTORS 1. Press ignition switch ON. 2. Check voltage between front air control connector M37 ...

    Readiness for inspection/maintenance (I/M) test
    Due to legal requirements in some states and Canadian Provinces, your vehicle may be required to be in what is called the “ready condition” for an Inspection/Maintenance (I/M) test of the emission control system. The vehicle is set to the “ready condition” when it is driven through c ...