Nissan Altima (L32) 2007-2012 Service Manual: Front wiper blade refill
Removal and Installation
REMOVAL
1. Remove the front wiper blade. Refer to WW-115, "FRONT WIPER BLADE : Removal and Installation".
2. Hold the wiper blade refill lip at the end (A) of the front wiper blade (1) with a suitable tool (B) as shown, and pull it firmly in the direction (C).
• U clip (part of the front wiper blade assembly) (D)
• If the wiper blade refill lip is torn due to wear, insert a suitable tool (A) into the space between the end of the wiper blade refill (1) and the front wiper blade (2) and pull the wiper blade refill (1) out as shown.
INSTALLATION
1. If the rib (A) has become detached from the wiper blade refill (1), check that the curve of the rib (A) is in the same direction as the curve of the wiper blade refill (1) and insert the rib (A) into the slit (B) in the wiper blade refill (1) as shown.
• If the rib (A) has a notch (B), insert the rib (A) into the wiper blade refill (1) so the notch (B) fits over the protrusion (C) in the wiper blade refill (1) as shown.
2. Insert the wiper blade refill (1) tip into the end of the front wiper blade (2) in the direction (C). Push the wiper blade refill (1) in while pressing it into the end of the front wiper blade (2) as shown. After the wiper blade refill is fully inserted, remove the holder (B).
• Tab [part of front wiper blade (2)] (A)
• Make sure to slide the refill into the front wiper blade so that the wiper blade refill is held by the tabs (A) on the front wiper blade as shown.
3. Push the wiper blade refill (1) until the tabs on the front wiper blade (2) fit into the stoppers (A) in the end of the wiper blade refill (1). Make sure the LOCK mark (B) on the wiper blade refill (1) is aligned with the lock point symbol (C) on the front wiper blade (2) as shown.
4. Before installing the front wiper blade assembly, make sure that the wiper blade refill (1) end is fully covered by the front wiper blade (2) in area (A) as shown.
5. Install the front wiper blade. Refer to WW-115, "FRONT WIPER BLADE : Removal and Installation".
Front wiper
Exploded View
1. Rib (part of wiper blade refill)
2. Wiper blade refill
3. Front RH wiper blade assembly (includes
wiper blade refill)
4. Front RH wiper arm
5. Wiper arm cap
6. Front wiper d ...
Front wiper blade
Removal and Installation
REMOVAL
1. Lift the front wiper arm and wiper blade assembly away from the
windshield.
2. Rotate the front wiper blade assembly and push the release tab
(A), then move ...
Other materials:
Malfunction indicator lamp
Description
The Malfunction Indicator Lamp (MIL) is located on the combination
meter.
The MIL will illuminate when the ignition switch is turned ON without
the engine running. This is a bulb check.
When the engine is started, the MIL should turn off. If the MIL
remains illuminated, the on ...
Cruise control operations
The cruise control allows driving at a speed between
25 - 89 MPH (40 - 144 km/h) without
keeping your foot on the accelerator pedal.
To turn on the cruise control, push the
ON·OFF switch on. The CRUISE indicator light in
the instrument panel will illuminate.
To set cruising speed, accelerat ...
Front wiper ARMS
Removal and Installation
REMOVAL
1. Turn wiper switch ON to operate wiper motor, and then turn wiper switch
OFF (auto stop).
2. Open hood, remove arm caps, and remove wiper arm nuts.
3. Raise wiper arm, and remove wiper arm from the vehicle.
INSTALLATION
1. Clean up the pivot area as sho ...
