Nissan Altima manuals

Nissan Altima (L32) 2007-2012 Service Manual: Intake valve timing control

System Diagram

System Description

INPUT/OUTPUT SIGNAL CHART

*: This signal is sent to the ECM through CAN communication line

SYSTEM DESCRIPTION

This mechanism hydraulically controls cam phases continuously with the fixed operating angle of the intake valve.

The ECM receives signals such as crankshaft position, camshaft position, engine speed, and engine coolant temperature. Then, the ECM sends ON/OFF pulse duty signals to the intake valve timing (IVT) control solenoid valve depending on driving status. This makes it possible to control the shut/open timing of the intake valve to increase engine torque in low/mid speed range and output in high-speed range.

Component Parts Location

1. Intake valve timing control solenoid valve

2. Ignition coil (with power transistor) and spark plug

3. Knock sensor, Crankshaft position sensor (POS)

4. Air fuel ratio (A/F) sensor 1

5. Camshaft position sensor (PHASE)

6. Engine coolant temperature sensor

7. Park/neutral position (PNP) switch

8. ECM

9. Refrigerant pressure sensor

10. Battery current sensor

11. IPDM E/R

12. Mass air flow sensor (with intake temperature sensor)

13. Tumble control valve actuator

14. EVAP service port

15. Electric throttle control actuator (with built in throttle position sensor and throttle control motor)

16. EVAP canister purge volume control solenoid valve

17. Fuel injector

18. Power steering pressure sensor

1. Battery

2. Fuel pump fuse (15A)

3. IPDM E/R

4. Brake master cylinder

5. Engine ground

6. Air cleaner assembly

7. Mass air flow sensor (with intake air temperature sensor)

8. Radiator hose (upper)

9. Engine coolant temperature sensor

10. Intake air duct

11. Camshaft position sensor (PHASE)

12. Tie rod (RH)

13. Power steering pressure sensor

14. Knock sensor

15. Engine oil cooler

16. Crankshaft position sensor (POS)

17. Drive shaft (RH)

1. Exhaust manifold cover

2. Air fuel ratio (A/F) sensor 1

3. Heated oxygen sensor 2 (This illustration is a view from under vehicle.)

4. Engine oil pan

1. EVAP service port

2. Intake air duct

3. EVAP canister purge volume control solenoid valve

4. Intake manifold collector

5. Park/neutral position (PNP) switch (CVT) (This illustration is view with air cleaner assembly removed.)

6. Park/neutral position (PNP) switch (M/T) (This illustration is view with air cleaner assembly removed.)

7. Intake valve timing control solenoid valve (This illustration is view with engine removed.)

8. Exhaust manifold cover

9. Air fuel ratio (A/F) sensor 1

10. Air fuel ratio (A/F) sensor 1 harness connector

11. Heated oxygen sensor 2 (This illustration is view from under vehicle.)

12. Heated oxygen sensor 2 harness connector (This illustration is view from under vehicle.)

13. Engine oil pan

14. Heated oxygen sensor 3 (This illustration is view form under vehicle.)

15. Heated oxygen sensor 3 harness connector (This illustration is view from under vehicle.)

1. Thermostat housing

2. Tumble control valve actuator

3. Throttle valve (This illustration is view with intake air duct removed.)

4. Electric throttle control actuator

5. Fuel injector harness connector

6. Condenser-2

7. Radiator hose (upper)

8. Battery

9. ECM

10. Fuel level sensor unit and fuel pump harness connector (This illustration is view with rear seat cushion and inspection hole cover removed.)

11. Fuel level sensor unit and fuel pump assembly

12. Fuel pressure regulator

13. Fuel tank temperature sensor

14. EVAP control system pressure sensor (This illustration is view with rear suspension member removed.)

15. EVAP canister vent control valve (This illustration is view with rear suspension member removed.)

16. EVAP canister (This illustration is view with rear suspension member removed.)

1. No.1 ignition coil

2. Cooling fan motor-1 harness connector

3. Cooling fan motor-2 harness connector

4. Refrigerant pressure sensor

5. Accelerator pedal position sensor

6. ASCD brake switch

10. Clutch pedal

11. ASCD steering switch

12. CANSEC switch

13. RESUME/ACCELERATE switch

14. SET/COAST switch

15. MAIN switch

Component Description

Evaporative emission system

System Diagram EVAPORATIVE EMISSION LINE DRAWING 1. Intake manifold collector 2. EVAP service port 3. EVAP canister purge volume control solenoid valve A. From next figure 1. EVAP contro ...

Tumble control valve control

System Diagram System Description INPUT/OUTPUT SIGNAL CHART *: ECM determines the start signal status by the signals of engine speed and battery voltage. SYSTEM DESCRIPTION Tumble control ...