Nissan Altima 2007-2012 Service Manual: Key cylinder switch
Description
For vehicles equipped with LH and RH anti-pinch system, the main power window and door lock/unlock switch detects condition of the door key cylinder switch and transmits to BCM as the LOCK or UNLOCK signal.
For vehicles equipped with LH anti-pinch system only, the front door lock assembly LH (key cylinder switch) transmits the LOCK or UNLOCK signal directly to the BCM.
Component Function Check
1.CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
Check KEY CYL UN-SW, KEY CYL UN-SW in “DATA MONITOR” mode for “POWER DOOR LOCK SYSTEM” with CONSULT-III. Refer to DLK-231, "Work Flow".
Is the inspection result normal? YES >> Key cylinder switch is OK.
NO >> Refer to DLK-306, "Diagnosis Procedure (With LH Anti-Pinch Only)".
Diagnosis Procedure
1.CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
1. Turn ignition switch ON.
2. Check voltage between BCM connector and ground.
Is the inspection result normal? YES >> Replace main power window and door lock/unlock switch. Refer to PWC-186, "Removal and Installation".
NO >> GO TO 2
2.CHECK DOOR KEY CYLINDER SWITCH GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect front door lock assembly LH (key cylinder switch) connector.
3. Check continuity between front door lock assembly LH (key cylinder switch) connector and ground.
Is the inspection result normal? YES >> GO TO 3
NO >> Repair or replace harness.
3.CHECK DOOR KEY CYLINDER SIGNAL CIRCUIT
1. Disconnect BCM connector M18.
2. Check continuity between front door lock assembly LH (key cylinder switch) connector and BCM connector M18.
3. Check continuity between front door lock assembly LH (key cylinder switch) connector and ground.
Is the inspection result normal? YES >> GO TO 4
NO >> Repair or replace harness.
4.CHECK DOOR KEY CYLINDER SWITCH
Check door key cylinder switch.
Refer to SEC-508, "Component Inspection".
Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> Replace front door lock assembly LH (key cylinder switch). Refer to DLK-451, "FRONT DOOR LOCK : Removal and Installation".
Component Inspection
COMPONENT INSPECTION
1.CHECK DOOR KEY CYLINDER SWITCH
Check front door lock assembly LH (key cylinder switch).
Is the inspection result normal? YES >> Key cylinder switch is OK.
NO >> Replace front door lock assembly LH (key cylinder switch). Refer to DLK-451, "FRONT DOOR LOCK : Removal and Installation".
Key slot illumination
Description Blinks when keyfob insertion is required. Component Function Check 1.CHECK FUNCTION Check key slot illumination (“KEY SLOT ILLUMI”) Active Test mode. Is the inspection resul ...Horn
Description Horn (high/low) is located inside of front bumper and operates when theft warning system is in alarm phase. Component Function Check 1.CHECK FUNCTION 1. Select HORN in “ACTIVE TES ...Other materials:
P1212 TCS Communication line
Description
This CAN communication line is used to control the smooth engine operation
during the TCS operation. Pulse
signals are exchanged between ECM and “ABS actuator and electric unit (control
unit)”.
Be sure to erase the malfunction information such as DTC not only for “ABS
ac ...
P0075, P0081 IVT control solenoid
valve
Description
Intake valve timing control solenoid valve is activated by ON/OFF
pulse duty (ratio) signals from the ECM.
The intake valve timing control solenoid valve changes the oil
amount and direction of flow via the intake valve timing control unit
or stops oil flow.
The longer pulse w ...
Air pressure monitor
Diagnosis Description
DESCRIPTION
During driving, the TPMS receives the signal transmitted from the transmitter
installed in each wheel, when
the tire pressure becomes low. The control unit (BCM) of this system has
pressure judgment and trouble diagnosis
functions.
When the TPMS detects l ...