Nissan Altima 2007-2012 Service Manual: P0125 ECT sensor

Description

The engine coolant temperature sensor is used to detect the engine coolant temperature. The sensor modifies a voltage signal from the ECM. The modified signal returns to the ECM as the engine coolant temperature input. The sensor uses a thermistor which is sensitive to the change in temperature. The electrical resistance of the thermistor decreases as temperature increases.

<Reference data>

*: These data are reference values and are measured between ECM terminals 46 (Engine coolant temperature sensor) and 52 (Sensor ground).

DTC Logic

DTC DETECTION LOGIC

NOTE: • If DTC P0125 is displayed with P0116, first perform the trouble diagnosis for DTC P0116. Refer to EC- 1210, "DTC Logic".

• If DTC P0125 is displayed with P0117 or P0118, first perform the trouble diagnosis for DTC P0117, P0118. Refer to EC-1212, "DTC Logic".

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

>> GO TO 2.

2.CHECK ENGINE COOLANT TEMPERATURE SENSOR FUNCTION

1. Turn ignition switch ON.

2. Select “DATA MONITOR” mode with CONSULT-III.

3. Check that “COOLAN TEMP/S” is above 10°C (50°F).

Follow the procedure “With CONSULT-III” above.

Is the temperature above 10°C (50°F)? YES >> INSPECTION END

NO >> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE

1. Start engine and run it for 65 minutes at idle speed.

If “COOLAN TEMP/S” increases to more than 10°C (50°F) within 65 minutes, stop engine because the test result will be OK.

CAUTION: Never overheat engine.

2. Check 1st trip DTC.

Follow the procedure “With CONSULT-III” above.

Is 1st trip DTC detected? YES >> EC-1219, "Diagnosis Procedure" NO >> INSPECTION END

Diagnosis Procedure

1.CHECK GROUND CONNECTION

1. Turn ignition switch OFF.

2. Check ground connection E9. Refer to Ground Inspection in GI-45, "Circuit Inspection".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace ground connection.

2.CHECK ENGINE COOLANT TEMPERATURE SENSOR

Refer to EC-1219, "Component Inspection".

Is the inspection result normal? YES >> GO TO 3.

NO >> Replace engine coolant temperature sensor.

3.CHECK THERMOSTAT OPERATION

When the engine is cold [lower than 70°C (158°F)] condition, grasp lower radiator hose and confirm that the engine coolant does not flow.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace thermostat. Refer to CO-46, "Removal and Installation".

4.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident".

>> INSPECTION END

Component Inspection

1.CHECK ENGINE COOLANT TEMPERATURE SENSOR

1. Turn ignition switch OFF.

2. Disconnect engine coolant temperature sensor harness connector.

3. Remove engine coolant temperature sensor.

4. Check resistance between engine coolant temperature sensor terminals as per the following.

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace engine coolant temperature sensor.

    P0122, P0123 TP sensor
    Description Electric throttle control actuator consists of throttle control motor, throttle position sensor, etc. The throttle position sensor responds to the throttle valve movement. The throt ...

    P0127 IAT sensor
    Description The intake air temperature sensor is built-into the mass air flow sensor (1). The sensor detects intake air temperature and transmits a signal to the ECM. The temperature sensing un ...

    Other materials:

    Secondary speed sensor
    Exploded View 1. CVT assembly 2. Shims 3. O-ring 4. Secondary Speed Sensor Removal and Installation Refer to the figure for removal and installation. CAUTION: • Do not reuse O-ring. • Apply CVT fluid to O-ring. • Insert the shims. • After installation is complete, check ...

    Camera image signal circuit (camera control unit to av control unit)
    Description Rear view camera image signals are transmitted from the rear view camera control unit to the AV control unit using the image signal circuits. Diagnosis Procedure 1.CHECK CAMERA IMAGE SIGNAL CIRCUIT CONTINUITY 1. Turn ignition switch OFF. 2. Disconnect rear view camera control ...

    Combination switch reading system
    System Diagram System Description OUTLINE • BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the status of each switch. • BCM is a combination of 5 output terminals (OUTPUT 1 - 5) and 5 input terminals (INPUT 1 - 5). It reads a m ...