Nissan Altima 2007-2012 Service Manual: P0127 IAT sensor

Description

The intake air temperature sensor is built-into the mass air flow sensor (1). The sensor detects intake air temperature and transmits a signal to the ECM.

The temperature sensing unit uses a thermistor which is sensitive to the change in temperature. Electrical resistance of the thermistor decreases in response to the rise in temperature.

<Reference data>

*: These data are reference values and are measured between ECM terminals 50 (Intake air temperature sensor) and 56 (Sensor ground).

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION: This test may be conducted with the drive wheels lifted in the shop or by driving the vehicle. If a road test is expected to be easier, it is unnecessary to lift the vehicle.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

1. Wait until engine coolant temperature is less than 90°C (194°F) - Turn ignition switch ON.

- Select “DATA MONITOR” mode with CONSULT-III.

- Check the engine coolant temperature.

- If the engine coolant temperature is not less than 90°C (194°F), turn ignition switch OFF and cool down engine.

NOTE: Perform the following steps before engine coolant temperature is approximately 90°C (194°F).

2. Turn ignition switch ON.

3. Select “DATA MONITOR” mode with CONSULT-III.

4. Start engine.

5. Hold vehicle speed at more than 70 km/h (43 MPH) for 100 consecutive seconds.

CAUTION: Always drive vehicle at a safe speed.

6. Check 1st trip DTC.

Follow the procedure “With CONSULT-III” above.

Is 1st trip DTC detected? YES >> Go to EC-1222, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK GROUND CONNECTION

1. Turn ignition switch OFF.

2. Check ground connection E9. Refer to Ground Inspection in GI-45, "Circuit Inspection".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace ground connection.

2.CHECK INTAKE AIR TEMPERATURE SENSOR

Refer to EC-1222, "Component Inspection".

Is the inspection result normal? YES >> GO TO 3.

NO >> Replace mass air flow sensor (with intake air temperature sensor).

3.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident".

>> INSPECTION END

Component Inspection

1.CHECK INTAKE AIR TEMPERATURE SENSOR

1. Turn ignition switch OFF.

2. Disconnect mass air flow sensor harness connector.

3. Check resistance between mass air flow sensor terminals as per the following.

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace mass air flow sensor (with intake air temperature sensor).

    P0125 ECT sensor
    Description The engine coolant temperature sensor is used to detect the engine coolant temperature. The sensor modifies a voltage signal from the ECM. The modified signal returns to the ECM as the ...

    P0128 Thermostat function
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0128 is displayed with DTC P0300, P0301, P0302, P0303, P0304, P0305 or P0306, first perform the trouble diagnosis for DTC P0300, P0301, P0302, P0303, ...

    Other materials:

    CVT position
    Inspection and Adjustment INSPECTION 1. Place selector lever in “P” position, and turn ignition switch ON (engine stop). 2. Make sure that selector lever can be shifted to other than “P” position when brake pedal is depressed. Also make sure that selector lever can be shifted fro ...

    Radiator
    Removal and Installation 1. Radiator 2. CVT oil cooler hose (if equipped) 3. Radiator hose (upper) 4. Radiator hose (lower) 5. Cooling fan 6. Reservoir tank 7. Reservoir hose 8. Radiator filler cap 9. Clamps A. To CVT (if equipped) B. To water outlet C. To water inlet WARNING: Never ...

    Lock-up and select control system
    System Diagram System Description • The torque converter clutch piston in the torque converter is engaged to eliminate torque converter slip to increase power transmission efficiency. • The torque converter clutch control valve operation is controlled by the torque converter clutch s ...