Nissan Altima 2007-2012 Service Manual: P0705 park/neutral position switch

Description

• The PNP switch is included in the control valve assembly.

• The PNP switch includes 4 transmission position switches.

• TCM judges the selector lever position by the PNP switch signal.

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION: Always drive vehicle at a safe speed.

NOTE:

If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF.

Then wait at least 10 seconds before performing the next test.

1.CHECK DTC DETECTION

1. Turn ignition switch ON.

2. Select “DATA MONITOR”.

3. Start engine.

4. Drive vehicle and maintain the following conditions for at least 2 consecutive seconds.

Follow the procedure “With CONSULT-III”.

Is “P0705 PNP SW/CIRC” detected? YES >> Go to TM-129, "Diagnosis Procedure".

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

Diagnosis Procedure

1.CHECK CVT POSITION

1. Disconnect CVT unit harness connector.

2. Remove control cable from manual lever. Refer to TM-256, "Exploded View".

3. Check PNP switch. Refer to TM-130, "Component Inspection".

Is the inspection result normal? YES >> Adjust CVT position. Refer to TM-253, "Inspection and Adjustment".

NO >> GO TO 2.

2. CHECK HARNESS BETWEEN TCM AND PNP SWITCH (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM harness connector.

3. Check continuity between TCM harness connector F16 (A) terminal 1, 2, 3, 4, 11 and CVT unit harness connector F46 (B) terminal 5, 14, 15, 18, 4.

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace damaged parts.

3. CHECK HARNESS BETWEEN TCM AND PNP SWITCH (PART 2)

Check continuity between TCM harness connector F16 terminal 1, 2, 3, 4, 11 and ground.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace damaged parts.

4.DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.

Is the inspection result normal? YES >> Replace the TCM. Refer to TM-254, "Exploded View".

NO >> Repair or replace damaged parts.

Component Inspection

1.CHECK PNP SWITCH

Check the continuity of the PNP switch by changing selector lever to various positions and checking continuity between CVT unit terminals and ground.

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace transaxle assembly. Refer to TM-259, "Exploded View".

    P0703 stop lamp switch
    Description BCM detects ON/OFF state of the stop lamp switch and transmits the data to the TCM via CAN communication by converting the data to a signal. DTC Logic DTC DETECTION LOGIC DTC CON ...

    P0710 cvt fluid temperature sensor
    Description The CVT fluid temperature sensor detects the CVT fluid temperature and sends a signal to the TCM. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE CAUTION: Always drive v ...

    Other materials:

    Vehicle load capacity
    Do not exceed the load limit of your vehicle shown as “The combined weight of occupants and cargo” on the Tire and Loading Information label. Do not exceed the number of occupants shown as “Seating Capacity” on the Tire and Loading Information label. To get “the combined weight of ...

    Pre-inspection for diagnostic
    Basic Inspection The engine start function, door lock function, power distribution system and NATS-IVIS/NMS in the Intelligent Key system are closely related to each other regarding control. Narrow down the functional area in question by performing basic inspection to identify which function ...

    P0740 torque converter clutch solenoid valve
    Description • The torque converter clutch solenoid valve is activated by the TCM in response to signals sent from the vehicle speed and accelerator pedal position sensors. Lock-up piston operation will then be controlled. • Lock-up operation, however, is prohibited when CVT fluid tempe ...