Nissan Altima 2007-2012 Service Manual: P0710 CVT fluid temperature sensor

Description

The CVT fluid temperature sensor detects the CVT fluid temperature and sends a signal to the TCM.

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION: Always drive vehicle at a safe speed.

NOTE: If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF.

Then wait at least 10 seconds before performing the next test.

1.CHECK DTC DETECTION (PART 1)

1. Turn ignition switch ON.

2. Select “DATA MONITOR”.

3. Check that output voltage of CVT fluid temperature sensor is within the range specified below.

ATF TEMP SEN : 0.16 – 2.03 V

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO-1 (“ATF TEMP SEN” indicates 0.15 or less.)>>Refer to TM-310, "Diagnosis Procedure".

NO-2 (“ATF TEMP SEN” indicates 2.04 or more.)>>GO TO 2.

2.CHECK DTC DETECTION (PART 2)

1. Turn ignition switch ON.

2. Select “DATA MONITOR”.

3. Start engine and maintain the following conditions for at least 14 minutes.

Follow the procedure “With CONSULT-III”.

Is “P0710 ATF TEMP SEN/CIRC” detected? YES >> Go to TM-310, "Diagnosis Procedure".

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

Diagnosis Procedure

1.CHECK CVT FLUID TEMPERATURE SENSOR CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

3. Check resistance between TCM harness connector F16 terminal 13, 25.

Is the inspection result normal? YES >> GO TO 5.

NO >> GO TO 2.

2.CHECK HARNESS BETWEEN TCM AND CVT UNIT (CVT TEMPERATURE SENSOR) (PART 1)

1. Disconnect CVT unit connector.

2. Check continuity between TCM harness connector F16 (A) terminal 13, 25 and CVT unit harness connector F46 (B) terminal 17, 19.

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace damaged parts.

3.CHECK HARNESS BETWEEN TCM AND CVT UNIT (CVT TEMPERATURE SENSOR) (PART 2)

Check continuity between TCM harness connector F16 terminal 13, 25 and ground.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace damaged parts.

4.CHECK CVT FLUID TEMPERATURE SENSOR

Check CVT fluid temperature sensor. Refer to TM-312, "Component Inspection (CVT Fluid Temperature Sensor)".

Is the inspection result normal? YES >> GO TO 6.

NO >> GO TO 5.

5.CHECK DTC

1. Turn ignition switch ON.

2. Perform “SELF-DIAG RESULTS” mode for “TRANSMISSION”.

Is only “P0710 ATF TEMP SEN/CIRC” detected? YES >> Replace control valve. Refer to TM-447, "Exploded View".

NO >> Replace transaxle assembly. Refer to TM-447, "Removal and Installation".

6.DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.

Is the inspection result normal? YES >> Replace TCM. Refer to TM-430, "Exploded View".

NO >> Repair or replace damaged parts.

Component Inspection (CVT Fluid Temperature Sensor)

1.CHECK CVT FLUID TEMPERATURE SENSOR

Check resistance between CVT unit terminals.

Is the inspection result normal? YES >> INSPECTION END

NO >> Perform “SELF-DIAG RESULTS” mode for “TRANSMISSION”.

    P0705 park/neutral position switch
    Description • The PNP switch assembly includes a transaxle range switch. • The transaxle range switch detects the selector lever position and sends a signal to the TCM. DTC Logic DTC DETE ...

    P0715 input speed sensor (pri speed sensor)
    Description The input speed sensor (primary speed sensor) detects the primary pulley revolution speed and sends a signal to the TCM. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE ...

    Other materials:

    P0300, P0301, P0302, P0303, P0304, P0305, P0306 Misfire
    DTC Logic DTC DETECTION LOGIC When a misfire occurs, engine speed will fluctuate. If the engine speed fluctuates enough to cause the crankshaft position (CKP) sensor (POS) signal to vary, ECM can determine that a misfire is occurring. The misfire detection logic consists of the following t ...

    Heater and Air Conditioner (manual) (if so equipped)
    1. Fan speed control / system OFF dial / air conditioning (A/C) button 2. Air flow control buttons 3. Temperature control dial / MAX A/C button 4. Air recirculation button 5. Rear window defroster button 6. Front windshield defrost button WARNING ● The air conditioner cooling functi ...

    Basic inspection
    DIAGNOSIS AND REPAIR WORKFLOW Work Flow OVERALL SEQUENCE DETAILED FLOW 1.INTERVIEW FOR MALFUNCTION Find out what the customer's concerns are. >> GO TO 2 2.SYMPTOM CHECK Verify the symptom from the customer's information. >> GO TO 3 3.BASIC INSPECTION Check the operation ...