Nissan Altima manuals

Nissan Altima (L32) 2007-2012 Service Manual: P0715 input speed sensor (pri speed sensor)

Description

The input speed sensor (primary speed sensor) detects the primary pulley revolution speed and sends a signal to the TCM.

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION: Always drive vehicle at a safe speed. NOTE: If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF.

Then wait at least 10 seconds before performing the next test.

1.CHECK DTC DETECTION

1. Turn ignition switch ON.

2. Select “DATA MONITOR”.

3. Start engine and maintain the following conditions for at least 5 consecutive seconds.

Follow the procedure “With CONSULT-III”.

Is “P0715 INPUT SPD SEN/CIRC” detected? YES >> Go to TM-135, "Diagnosis Procedure".

NO >> Check itermittent incident. Refer to GI-42, "Intermittent Incident".

Diagnosis Procedure

1.CHECK INPUT SPEED SENSOR (PRIMARY SPEED SENSOR)

1. Start engine.

2. Check voltage between TCM harness connector F16 terminal 25 and 26.

3. If OK, check the pulse when vehicle cruises.

Is the inspection result normal? OK >> GO TO 7.

NG - 1 >> Battery voltage is not supplied: GO TO 2.

NG - 2 >> Battery voltage is supplied, but there is a malfunction in the frequency: GO TO 4.

2. CHECK HARNESS BETWEEN TCM AND CVT UNIT HARNESS CONNECTOR (SENSOR POWER AND SENSOR GROUND) (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM harness connector and CVT unit harness connector.

3. Check continuity between TCM harness connector F16 (A) terminal 25 and 26 and CVT unit harness connector F46 (B) terminal 19 and 20.

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace damaged parts.

3. CHECK HARNESS BETWEEN TCM AND CVT UNIT HARNESS CONNECTOR (SENSOR POWER AND SENSOR GROUND) (PART 2)

Check continuity between TCM harness connector F16 terminal 25 and 26 and ground.

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace damaged parts.

4. CHECK HARNESS BETWEEN TCM AND CVT UNIT HARNESS CONNECTOR [INPUT SPEED SENSOR (PRIMARY SPEED SENSOR)] (PART 1)

1. Turn ignition switch OFF.

2. Disconnect TCM harness connector and CVT unit harness connector.

3. Check continuity between TCM harness connector F16 (A) terminal 33 and CVT unit harness connector F46 (B) terminal 22.

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace damaged parts.

5. CHECK HARNESS BETWEEN TCM AND CVT UNIT HARNESS CONNECTOR [INPUT SPEED SENSOR (PRIMARY SPEED SENSOR)] (PART 2)

Check continuity between TCM harness connector F16 terminal 33 and ground.

Is the inspection result normal? YES >> GO TO 6.

>> Repair or replace damaged parts.

6. CHECK THE TCM SHORT

Replace same type TCM, perform self-diagnosis check. Erase self-diagnostic results and then drive the vehicle [10 km/h (6 MPH) or more], perform self-diagnosis check. Refer to TM-135, "DTC Logic".

Is the “P0715 INPUT SPD SEN/CIRC” detected again? YES >> GO TO 7.

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

7.DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.

Is the inspection result normal? YES >> Replace TCM. Refer to TM-254, "Exploded View".

NO >> Repair or replace damaged parts.

P0710 cvt fluid temperature sensor

Description The CVT fluid temperature sensor detects the CVT fluid temperature and sends a signal to the TCM. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE CAUTION: Always drive v ...

P0720 vehicle speed sensor cvt (secondary speed sensor)

Description The vehicle speed sensor CVT [output speed sensor (secondary speed sensor)] detects the revolution of the CVT output shaft and emits a pulse signal. The pulse signal is sent to the TCM ...