Nissan Altima 2007-2012 Service Manual: P0745 line pressure solenoid valve
Description
The pressure control solenoid valve A (line pressure solenoid valve) regulates the oil pump discharge pressure to suit the driving condition in response to a signal sent from the TCM.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
NOTE: If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF.
Then wait at least 10 seconds before performing the next test.
1.CHECK DTC DETECTION
1. Turn ignition switch ON.
2. Start engine and wait at least 5 seconds.
3. Perform “SELF-DIAG RESULTS” mode for “TRANSMISSION”.
Follow the procedure “With CONSULT-III”.
Is “P0745 L/PRESS SOL/CIRC” detected? YES >> Go to TM-148, "Diagnosis Procedure".
NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
Diagnosis Procedure
1.CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE) CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect TCM harness connector.
3. Check resistance between TCM harness connector F16 terminal 40 and ground.
Is the inspection result normal? YES >> GO TO 5.
NO >> GO TO 2.
2.CHECK HARNESS BETWEEN TCM AND CVT UNIT [PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)] (PART 1)
1. Disconnect CVT unit connector.
2. Check continuity between TCM harness connector F16 (A) terminal 40 and CVT unit harness connector F46 (B) terminal 2.
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace damaged parts.
3.CHECK HARNESS BETWEEN TCM AND CVT UNIT [PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)] (PART 2)
Check continuity between TCM vehicle side harness connector F16 terminal 40 and ground.
Is the inspection result normal? YES >> GO TO 4.
NO >> Repair or replace damaged parts.
4.CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)
Check pressure control solenoid valve A (line pressure solenoid valve). Refer to TM-149, "Component Inspection [Pressure Control Solenoid Valve A (Line Pressure Solenoid Valve)]" Is the inspection result normal? YES >> GO TO 5.
NO >> Replace transaxle assembly. Refer to TM-259, "Exploded View".
5.DETECT MALFUNCTIONING ITEMS
Check TCM connector pin terminals for damage or loose connection with harness connector.
Is the inspection result normal? YES >> Replace TCM. Refer to TM-254, "Exploded View".
NO >> Repair or replace damaged parts.
Component Inspection [Pressure Control Solenoid Valve A (Line Pressure Solenoid Valve)
1.CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)
Check resistance between CVT unit terminal 2 and ground.
Is the inspection result normal? YES >> INSPECTION END
NO >> Replace transaxle assembly. Refer to TM-259, "Exploded View".
P0744 a/t tcc s/v function (lock -up)
Description
This malfunction is detected when the torque converter clutch does not
lock-up as instructed by the TCM. This
is not only caused by electrical malfunction (circuits open or shorted), ...
P0746 pressure control solenoid A
performance (line pressure solenoid
valve)
Description
The pressure control solenoid valve A (line pressure solenoid valve)
regulates the oil pump discharge pressure
to suit the driving condition in response to a signal sent from the TCM.
...
Other materials:
Measurement of weights
Secure loose items to prevent weight
shifts that could affect the balance of your
vehicle. When the vehicle is loaded, drive
to a scale and weigh the front and the rear
wheels separately to determine axle
loads. Individual axle loads should not exceed
either of the gross axle weight ratings
( ...
P0715 input speed sensor (pri speed
sensor)
Description
The input speed sensor (primary speed sensor) detects the primary pulley
revolution speed and sends a signal
to the TCM.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE:
If “DTC CONFIRMATION PROCEDURE” has be ...
Front passenger air bag module
Removal and Installation
REMOVAL
CAUTION:
• Before servicing, turn ignition switch OFF, disconnect both battery terminals
and wait at
least three minutes.
• Do not use air tools or electric tools for servicing.
• Always work from the side of air bag module. Do not work from the fro ...