Nissan Altima 2007-2012 Service Manual: P0841 pressure sensor function

Description

Using the engine load (throttle position), the primary pulley revolution speed, and the secondary pulley revolution speed as input signal, TCM changes the operating pressure of the primary pulley and the secondary pulley and changes the groove width of the pulley to control the gear ratio.

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION: Always drive vehicle at a safe speed.

NOTE: If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF.

Then wait at least 10 seconds before performing the next test.

1.CHECK DTC DETECTION

1. Turn ignition switch ON.

2. Select “DATA MONITOR”.

3. Start engine and maintain the following conditions for at least 12 consecutive seconds.

Is “P0841 PRESS SEN/FNCTN” detected? YES >> Go to TM-163, "Diagnosis Procedure".

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

Diagnosis Procedure

1.CHECK LINE PRESSURE

Perform line pressure test. Refer to TM-247, "Inspection and Judgment".

Is the inspection result normal? YES >> .GO TO 2.

NO >> Repair or replace damaged parts. Refer to TM-247, "Inspection and Judgment".

2.CHECK TRANSMISSION FLUID PRESSURE SENSOR A (SECONDARY PRESSURE SENSOR) SYSTEM

Check transmission fluid pressure sensor A (secondary pressure sensor) system. Refer to TM-160, "Description".

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace damaged parts.

3.CHECK TRANSMISSION FLUID PRESSURE SENSOR B (PRIMARY PRESSURE SENSOR) SYSTEM

Check transmission fluid pressure sensor B (primary pressure sensor) system. Refer to TM-166, "Description".

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace damaged parts.

4.CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)

1. Turn ignition switch OFF.

2. Disconnect CVT unit harness connector.

3. Check pressure control solenoid valve A (line pressure solenoid valve). Refer to TM-164, "Component Inspection [Pressure Control Solenoid Valve A (Line Pressure Solenoid Valve)]".

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace damaged parts.

5.CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)

Check pressure control solenoid valve B (secondary pressure solenoid valve). Refer to TM-164, "Component Inspection [Pressure Control Solenoid Valve B (Secondary Pressure Solenoid Valve)]".

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace damaged parts.

6.CHECK STEP MOTOR SYSTEM

Check step motor system. Refer to TM-184, "Description".

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace damaged parts.

7.DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.

Is the inspection result normal? YES >> Replace TCM. Refer to TM-254, "Exploded View".

NO >> Repair or replace damaged parts.

Component Inspection [Pressure Control Solenoid Valve A (Line Pressure Solenoid Valve)

1.CHECK PRESSURE CONTROL SOLENOID VALVE A (LINE PRESSURE SOLENOID VALVE)

Check resistance between CVT unit terminal 2 and ground.

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace transaxle assembly. Refer to TM-259, "Exploded View".

Component Inspection [Pressure Control Solenoid Valve B (Secondary Pressure Solenoid Valve)

1.CHECK PRESSURE CONTROL SOLENOID VALVE B (SECONDARY PRESSURE SOLENOID VALVE)

Check resistance between CVT unit terminal 3 and ground.

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace transaxle assembly. Refer to TM-259, "Exploded View".

    P0840 transmission fluid pressure sensor A (sec pressure sensor)
    Description The transmission fluid pressure sensor A (secondary pressure sensor) detects secondary pressure of CVT and sends TCM the signal. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PRO ...

    P0845 transmission fluid pressure sensor B (pri pressure sensor)
    Description The transmission fluid pressure sensor B (primary pressure sensor) detects primary pressure of CVT and sends TCM the signal. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCE ...

    Other materials:

    B261A push-button ignition switch
    Description IPDM E/R transmits the push-button ignition switch status via CAN communication to BCM. BCM receives push-button ignition switch status by hardwire input. BCM compares the 2 signals for mismatch. DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B261A is displayed with DTC U1000, ...

    High-pressure pipe
    Removal and Installation for High-Pressure Pipe QR25DE Removal 1. Discharge the refrigerant. Refer to HA-24, "HFC-134a (R-134a) Service Procedure". 2. Remove the strut tower bar. Refer to FSU-12, "Exploded View". 3. Remove the upper cowl. Refer to EXT-18, "Remova ...

    Evaporative emission system
    System Diagram System Description INPUT/OUTPUT SIGNAL CHART *1: ECM determines the start signal status by the signals of engine speed and battery voltage. *2: This signal is sent to the ECM via the CAN communication line. SYSTEM DESCRIPTION The evaporative emission system is used to ...