Nissan Altima 2007-2012 Service Manual: P1740 lock-up select solenoid valve

Description

• Lock-up select solenoid valve controls lock-up clutch pressure or forward clutch pressure (reverse brake pressure).

• When controlling lock-up clutch, the valve is turned OFF. When controlling forward clutch, it is turned ON.

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

CAUTION: Always drive vehicle at a safe speed. NOTE: If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF.

Then wait at least 10 seconds before performing the next test.

1.CHECK DTC DETECTION

1. Turn ignition switch ON.

2. Select “DATA MONITOR”.

3. Start engine and maintain the following conditions for at least 5 consecutive seconds.

Follow the procedure “With CONSULT-III”.

Is “P1740 LU-SLCT SOL/CIRC” detected? YES >> Go to TM-181, "Diagnosis Procedure".

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

Diagnosis Procedure

1.CHECK LOCK-UP SELECT SOLENOID VALVE CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect TCM harness connector.

3. Check resistance between TCM harness connector F16 terminal 37 and ground.

Is the inspection result normal? YES >> GO TO 5.

NO >> GO TO 2.

2.CHECK HARNESS BETWEEN TCM AND CVT UNIT (LOCK-UP SELECT SOLENOID VALVE) (PART 1)

1. Disconnect CVT unit harness connector.

2. Check continuity between TCM harness connector F16 (A) terminal 37 and CVT unit harness connector F46 (B) terminal 13.

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace damaged parts.

3.CHECK HARNESS BETWEEN TCM AND CVT UNIT (LOCK-UP SELECT SOLENOID VALVE) (PART 2)

Check continuity between TCM harness connector F16 terminal 37 and ground.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace damaged parts.

4.CHECK LOCK-UP SELECT SOLENOID VALVE

Check lock-up select solenoid valve. Refer to TM-182, "Component Inspection (Lock-up Select Solenoid Valve)".

Is the inspection result normal? YES >> GO TO 5.

NO >> Replace transaxle assembly. Refer to TM-259, "Exploded View".

5.DETECT MALFUNCTIONING ITEMS

Check TCM connector pin terminals for damage or loose connection with harness connector.

Is the inspection result normal? YES >> Replace TCM. Refer to TM-254, "Exploded View".

NO >> Repair or replace damaged parts.

Component Inspection (Lock-up Select Solenoid Valve)

1.CHECK LOCK-UP SELECT SOLENOID VALVE

Check resistance between CVT unit connector terminal and ground.

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace transaxle assembly. Refer to TM-259, "Exploded View".

    P1726 electric throttle control system
    Description Electric throttle control actuator consists of throttle control motor, accelerator pedal position sensor, throttle position sensor etc. The actuator sends a signal to the ECM, and ECM ...

    P1745 line pressure control
    Description The pressure control solenoid valve A (line pressure solenoid valve) regulates the oil pump discharge pressure to suit the driving condition in response to a signal sent from the TCM. ...

    Other materials:

    P0460 Fuel level sensor
    Description The fuel level sensor is mounted in the fuel level sensor unit. The sensor detects a fuel level in the fuel tank and transmits a signal to the combination meter. The combination meter sends the fuel level sensor signal to the ECM via the CAN communication line. It consists of ...

    Air breather hose
    Exploded View 1. Air cleaner 2. Air breather hose 3. Transaxle assembly 4. Heater pipe 5. Clip A. Paint mark Removal and Installation CAUTION: • Install air breather hose with paint mark facing front. • Insert air breather hose onto air breather tube until overlap area reaches t ...

    On-vehicle maintenance
    M/T OIL Draining 1. Start engine and let it run to warm up transaxle oil. 2. Stop engine and remove the drain plug to drain the oil. 3. Install the drain plug with a new gasket to the transaxle case. Tighten the drain plug to the specified torque. Refer to TM-28, "Exploded View" ...