Nissan Altima 2007-2012 Service Manual: P2119 Electric throttle control actuator

Description

Electric throttle control actuator consists of throttle control motor, throttle position sensor, etc.

The throttle control motor is operated by the ECM and it opens and closes the throttle valve.

The throttle position sensor detects the throttle valve position, and the opening and closing speed of the throttle valve and sends the voltage signals to the ECM. The ECM judges the current opening angle of the throttle valve from these signals and opens/closes the throttle valve in response to driving conditions via the throttle control motor.

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION A AND B

1. Turn ignition switch ON and wait at least 1 second.

2. Shift selector lever position to D (CVT) or 1st position (M/T) and wait at least 3 seconds.

3. Shift selector lever position to P (CVT) or neutral position (M/T).

4. Turn ignition switch OFF and wait at least 10 seconds.

5. Turn ignition switch ON and wait at least 1 second.

6. Shift selector lever position to D (CVT) or 1st position (M/T) and wait at least 3 seconds.

7. Shift selector lever position to P (CVT) or neutral position (M/T).

8. Turn ignition switch OFF, wait at least 10 seconds, and then turn ON.

9. Check DTC.

Is DTC detected? YES >> Go to EC-1447, "Diagnosis Procedure".

NO >> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION C

1. Turn ignition switch ON and wait at least 1 second.

2. Shift selector lever position to D (CVT) or 1st position (M/T) and wait at least 3 seconds.

3. Shift selector lever position to N, P (CVT) neutral position (M/T).

4. Start engine and let it idle for 3 seconds.

5. Check DTC.

Is DTC detected? YES >> Go to EC-1447, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY

1. Turn ignition switch OFF.

2. Remove the intake air duct.

3. Check if foreign matter is caught between the throttle valve (1) and the housing.

- Electric throttle control actuator (2)

Is the inspection result normal? YES >> GO TO 2.

NO >> Remove the foreign matter and clean the electric throttle control actuator inside.

2.REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR

1. Replace electric throttle control actuator.

2. Go to EC-1393, "Special Repair Requirement".

>> INSPECTION END

Special Repair Requirement

1.PERFORM THROTTLE VALVE CLOSED POSITION LEARNING

Refer to EC-1053, "THROTTLE VALVE CLOSED POSITION LEARNING : Special Repair Requirement" >> GO TO 2.

2.PERFORM IDLE AIR VOLUME LEARNING

Refer to EC-1053, "IDLE AIR VOLUME LEARNING : Special Repair Requirement" >> END

    P2118 Throttle control motor
    Description The throttle control motor is operated by the ECM and it opens and closes the throttle valve. The current opening angle of the throttle valve is detected by the throttle position s ...

    P2122, P2123 APP Sensor
    Description The accelerator pedal position sensor is installed on the upper end of the accelerator pedal assembly. The sensor detects the accelerator position and sends a signal to the ECM. Acce ...

    Other materials:

    P1722 Estm vehicle speed signal
    Description The vehicle speed signal is transmitted from ABS actuator and electric unit (control unit) to TCM by CAN communication line. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE CAUTION: Always drive vehicle at a safe speed. NOTE: If “DTC CONFIRMATION PROCEDURE” has ...

    M&A branch line circuit
    Diagnosis Procedure INSPECTION PROCEDURE 1.CHECK CONNECTOR 1. Turn the ignition switch OFF. 2. Disconnect the battery cable from the negative terminal. 3. Check the terminals and connectors of the combination meter for damage, bend and loose connection (unit side and connector side). ...

    B1065 – B1068, B1070 – B1073 passenger airbag module
    Description DTC B1065 – B1068, B1070 – B1073 PASSENGER AIR BAG MODULE The passenger air bag module is dual stage and wired to the air bag diagnosis sensor unit. The air bag diagnosis sensor unit will monitor for opens and shorts in detected lines to the passenger air bag module. PART LOC ...