Nissan Altima 2007-2012 Service Manual: Passenger side

Description

• BCM supplies power.

• Power window motor RH will be operated if power window and door lock/unlock switch RH is operated.

Component Function Check

Power Window And Door Lock/unlock Switch RH

1. CHECK POWER WINDOW MOTOR RH FUNCTION

Does power window motor RH operate with power window and door lock/unlock switch RH operation? Is the inspection result normal? YES >> Power window and door lock/unlock switch RH power supply and ground circuit are OK.

NO >> Refer to PWC-22, "PASSENGER SIDE : Diagnosis Procedure".

Diagnosis Procedure

Power Window And Door Lock/Unlock Switch RH Power Supply Circuit Check

1. CHECK POWER SUPPLY CIRCUIT

1. Turn ignition switch ON.

2. Check voltage between power window and door lock/unlock switch RH connector and ground.

Is the measurement value within the specification? YES >> GO TO 3

NO >> GO TO 2

2. CHECK HARNESS CONTINUITY

1. Turn ignition switch OFF.

2. Disconnect BCM and power window and door lock/unlock switch RH.

3. Check continuity between BCM connector (A) and power window and door lock/unlock switch RH connector (B).

4. Check continuity between BCM connector (A) and ground.

Is the inspection result normal? YES >> GO TO 4

NO >> Repair or replace harness.

3. CHECK HARNESS CONTINUITY (POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH)

1. Turn ignition switch OFF.

2. Disconnect main power window and door lock/unlock switch and power window and door lock/unlock switch RH.

3. Check continuity between main power window and door lock/ unlock switch connector (A) and power window and door lock/ unlock switch RH connector (B).

4. Check continuity between main power window and door lock/unlock switch connector (A) and ground.

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Repair or replace harness.

4. CHECK BCM OUTPUT SIGNAL

1. Connect BCM.

2. Turn ignition switch ON.

3. Check voltage between BCM connector and ground.

Is the measurement value within the specification? YES >> GO TO 5

NO >> Repair or replace harness.

5. CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH

Check power window and door lock/unlock switch RH.

Refer to PWC-23, "PASSENGER SIDE : Component Inspection".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Replace power window and door lock/unlock switch RH. Refer to PWC-91, "Removal and Installation".

Component Inspection

COMPONENT INSPECTION

1. CHECK POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH RH

Check power window and door lock/unlock switch RH.

Is the inspection result normal? YES >> Power window and door lock/unlock switch RH is OK.

NO >> Replace power window and door lock/unlock switch RH. Refer to PWC-91, "Removal and Installation".

    Power window main switch
    Description • BCM supplies power. • It operates each power window motor via corresponding power window switch and makes window move up/ down when main power window and door lock/unlock swit ...

    Other materials:

    The fuel gauge pointer does not move
    Description Fuel gauge needle will not move from a certain position. Diagnosis Procedure 1.CHECK COMBINATION METER INPUT SIGNAL 1. Select “METER/M&A” on CONSULT-III. 2. Using “FUEL METER” of “DATA MONITOR”, compare the monitor value with the fuel gauge reading on the combi ...

    Ignition signal
    Description The ignition signal from the ECM is sent to and amplified by the power transistor. The power transistor turns ON and OFF the ignition coil primary circuit. This ON/OFF operation induces the proper high voltage in the coil secondary circuit. Component Function Check 1.INSPECTION ...

    Service data and specifications (SDS)
    General Specification CAUTION: • Use only Genuine NISSAN CVT Fluid NS-2. Do not mix with other fluid. • Using CVT fluid other than Genuine NISSAN CVT Fluid NS-2 will deteriorate in driveability and CVT durability, and may damage the CVT, which is not covered by the NISSAN new vehicle l ...