Nissan Altima Owners Manual: Rear-facing child restraint installation using the seat belts

WARNING


WARNING

The three-point seat belt with Automatic Locking Retractor (ALR) must be used when installing a child restraint. Failure to use the ALR mode will result in the child restraint not being properly secured. The restraint could tip over or be loose and cause injury to a child in a sudden stop or collision. Also, it can change the operation of the front passenger air bag. See “Front passenger air bag and status light” later in this section.

Rear-facing – step 1


Rear-facing – step 1

Refer to all Warnings and Cautions in the “Child safety” and “Child restraints” sections before installing a child restraint.

Follow these steps to install a rear-facing child restraint using the vehicle seat belts in the rear seats:
1. Child restraints for infants must be used in the rear-facing direction and therefore must not be used in the front seat

. Position the child restraint on the seat.

Always follow the restraint manufacturer’s instructions.

Rear-facing – step 2


Rear-facing – step 2

2. Route the seat belt tongue through the child restraint and insert it into the buckle until you hear and feel the latch engage. Be sure to follow the child restraint manufacturer’s instructions for belt routing.

Rear-facing – step 3


Rear-facing – step 3

3. Pull the shoulder belt until the belt is fully extended. At this time, the seat belt retractor is in the Automatic Locking Retractor (ALR) mode (child restraint mode). It reverts to the Emergency Locking Retractor (ELR) mode when the seat belt is fully retracted.

Rear-facing – step 4


Rear-facing – step 4

4. Allow the seat belt to retract. Pull up on the shoulder belt to remove any slack in the belt.

Rear-facing – step 5


Rear-facing – step 5

5. Remove any additional slack from the seat belt; press downward and rearward firmly in the center of the child restraint to compress the vehicle seat cushion and seatback while pulling up on the seat belt.

Rear-facing – step 6


Rear-facing – step 6

6. After attaching the child restraint, test it before you place the child in it. Push it from side to side while holding the child restraint near the seat belt path. The child restraint should not move more than 1 inch (25 mm), from side to side. Try to tug it forward and check to see if the belt holds the restraint in place.

If the restraint is not secure, tighten the seat belt as necessary, or put the restraint in another seat and test it again. You may need to try a different child restraint. Not all child restraints fit in all types of vehicles.

7. Check to make sure that the child restraint is properly secured prior to each use. If the seat belt is not locked, repeat steps 1 through 6.

After the child restraint is removed and the seat belt fully retracted, the ALR mode (child restraint mode) is canceled.

    Rear-facing child restraint installation using LATCH
    Refer to all Warnings and Cautions in the “Child Safety” and “Child Restraint” sections before installing a child restraint. Follow these steps to install a rear-facing child restraint u ...

    Forward-facing child restraint installation using LATCH
    Refer to all Warnings and Cautions in the “Child Safety” and “Child Restraint” sections before installing a child restraint. Follow these steps to install a forward-facing child restrain ...

    Other materials:

    Vehicle speed signal circuit
    Description • Combination meter sends vehicle speed signal to power steering control unit. Diagnosis Procedure 1.PERFORM COMBINATION METER SELF-DIAGNOSIS Perform combination meter self-diagnosis. Is any error system detected? YES >> Check the error system. NO >> GO TO 2. ...

    P0826 manual mode switch
    Description Manual mode switch is installed in CVT control device. The manual mode switch sends shift up and shift down switch signals to TCM. TCM sends the switch signals to combination meter via CAN communication line. Then manual mode switch position is indicated on the CVT position ind ...

    Rear tweeter (coupe)
    Description The audio unit sends audio signals to the BOSE speaker amp. The BOSE speaker amp. amplifies the audio signals before sending them to the rear tweeters using the audio signal circuits. Diagnosis Procedure 1.HARNESS CHECK 1. Disconnect BOSE speaker amp. connectors B121, B122 and ...