Nissan Altima 2007-2012 Service Manual: Rear power window switch

Description

• BCM supplies power.

• Rear power window motor will be operated if rear power window switch is operated. Rear power window switch.

 Component Function Check

Rear Power Window Switch

1. CHECK REAR POWER WINDOW MOTOR FUNCTION

Does rear power window motor operate with rear power window switch operation? Is the inspection result normal?

YES >> Rear power window switch power supply and ground circuit are OK.

NO >> Refer to PWC-111, "REAR POWER WINDOW SWITCH : Diagnosis Procedure".

Diagnosis Procedur

Rear Power Window Switch Power Supply Circuit Check

1. CHECK POWER SUPPLY CIRCUIT

1. Turn ignition switch ON.

2. Check voltage between rear power window switch connector and ground.

Is the measurement value within the specification? YES >> GO TO 2 (Rear power window switch LH) YES >> GO TO 3 (Rear power window switch RH) NO >> GO TO 4

2. CHECK HARNESS CONTINUITY (REAR POWER WINDOW SWITCH LH)

1. Turn ignition switch OFF.

2. Disconnect main power window and door lock/unlock switch and rear power window switch LH.

3. Check continuity between main power window and door lock/ unlock switch connector (A) and rear power window switch LH connector (B).

4. Check continuity between main power window and door lock/unlock switchh connector (A) and ground.

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Repair or replace harness.

3. CHECK HARNESS CONTINUITY (REAR POWER WINDOW SWITCH RH)

1. Turn ignition switch OFF.

2. Disconnect main power window and door lock/unlock switch and rear power window switch RH.

3. Check continuity between main power window and door lock/ unlock switch connector (A) and rear power window switch RH connector (B).

4. Check continuity between main power window and door lock/unlock switch connector (A) and ground.

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Repair or replace harness.

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Repair or replace harness.

4. CHECK HARNESS CONTINUITY

1. Disconnect BCM and rear power window switch.

2. Check continuity between BCM connector (A) and rear power window switch connector (B).

3. Check continuity between BCM connector and ground.

Is the inspection result normal? YES >> GO TO 5

NO >> Repair or replace harness.

5. CHECK REAR POWER WINDOW SWITCH

Check rear power window switch.

Refer to PWC-112, "REAR POWER WINDOW SWITCH : Component Inspection".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Replace rear power window switch. Refer to PWC-186, "Removal and Installation".

 Component Inspection

1. CHECK REAR POWER WINDOW SWITCH

Check rear power window switch.

Is the inspection result normal? YES >> Rear power window switch is OK.

NO >> Replace rear power window switch. Refer to PWC-186, "Removal and Installation".

    Front power window switch
    Description • BCM supplies power. • Front power window motor RH will be operated if power window and door lock/unlock switch RH is operated. Component Function Check Power Window And Door ...

    Power window motor
    ...

    Other materials:

    Air conditioner control
    System Diagram CONTROL SYSTEM The control system consists of input sensors, switches, front air control and outputs. The relationship of these components is shown in the figure below: System Description CONTROL OPERATION 1. Blower control dial 2: Air recirculation switch 3: Defroster ...

    Seat belt buckle switch signal circuit
    Description Transmits a seat belt buckle switch signal to the combination meter. Component Function Check 1. CHECK COMBINATION METER INPUT SIGNAL Select “DATA MONITOR” for “METER/M&A” and check the “BUCKLE SW” monitor value. >> Inspection End. Diagnosis Procedure 1. ...

    Cylinder block
    Disassembly and Assembly 1. Cylinder block 2. O-ring 3. Crankshaft position sensor (POS) 4. Knock sensor 5. Cylinder block heater (if equipped) 6. Lower cylinder block 7. Lower cylinder block bolt 8. Snap ring 9. Connecting rod 10. Connecting rod bearing 11. Connecting rod bearing cap ...