Nissan Altima 2007-2012 Service Manual: SRS air bag system

SRS Configuration

The air bag deploys if the air bag diagnosis sensor unit is activated while the ignition switch is in the ON or START position.

The collision modes for which supplemental restraint systems are activated are different among the SRS systems.

For example, the driver air bag module, front passenger air bag module and front seat belt pre-tensioners are activated in a frontal collision but not in a side collision.

SRS configurations for some collision modes are as follows:

SRS Component Parts Location

1. Crash zone sensor

2. Spiral cable

3. Front passenger air bag off indicator (if equipped)

4. Front LH seatbelt pre-tensioner LH side air bag (satellite) sensor (if equipped)

5. Air bag diagnosis sensor unit

6. Front LH side air bag module (if equipped)

7. Seat belt buckle switch (LH) Seat belt buckle switch (RH)

8. Occupant classification system control unit and sensor mat (if equipped)

9. Front RH seatbelt pre-tensioner RH side air bag (satellite) sensor (if equipped)

10. Front RH side air bag module (if equipped)

11. RH side curtain air bag module (if equipped)

12. LH side curtain air bag module (if equipped)

13. Front passenger air bag module

14. Driver air bag module

Driver Air Bag Module

The driver air bag module is dual stage and located in the steering wheel assembly. It operates with the SRS system in a frontal collision exceeding a specified level.

Front Passenger Air Bag Module

The front passenger air bag module is located behind the instrument panel assembly. It operates with the SRS system in a frontal collision exceeding a specified level. Refer to SRC-10, "Occupant Classification System (OCS)" for more information.

Front Side Air Bag

Front side air bag modules are built into the front seatback assemblies.

Vehicles with side air bags are equipped with labels as shown.

Side Curtain Air Bag

Side curtain air bag modules are located above the vehicle headlining.

Vehicles with side curtain air bags are equipped with labels as shown.

Front Seat Belt Pre-tensioner with Load Limiter

The seat belt pre-tensioner system with load limiter is installed for both the driver's seat and the front passenger's seat. It operates simultaneously with the SRS air bag system in the event of a frontal collision with an impact exceeding a specified level.

When the frontal collision with an impact exceeding a specified level occurs, seat belt slack resulting from clothing or other factors is immediately taken up by the pre-tensioner. Vehicle passengers are securely restrained.

When passengers in a vehicle are thrown forward in a collision and the restraining force of the seat belt exceeds a specified level, the load limiter permits the specified extension of the seat belt by the twisting of the ELR shaft, and a relaxation of the chest-area seat belt web tension while maintaining force.

Direct-connect SRS Component Connectors

The following SRS components use direct-connect style harness connectors.

• Driver front air bag module

• Passenger front air bag module

• LH side curtain air bag module

• RH side curtain air bag module

• Front LH seat belt pre-tensioner

• Front RH seat belt pre-tensioner

Always pull up to release locking tab prior to removing connector from SRS component.

Always push down to lock locking tab after installing connector to SRS component. When locked, the locking tab is level with the connector housing.

    Occupant classification system
    System Diagram Occupant Classification System (OCS) The occupant classification system (OCS) identifies if a child or child seat is present in the front passenger seat. The OCS receives input ...

    Other materials:

    TCM branch line circuit
    Diagnosis Procedure INSPECTION PROCEDURE 1.CHECK CONNECTOR 1. Turn the ignition switch OFF. 2. Disconnect the battery cable from the negative terminal. 3. Check the following terminals and connectors for damage, bend and loose connection (unit side and connector side). - TCM - Harnes ...

    BCM
    Diagnosis Procedure 1. CHECK FUSE AND FUSIBLE LINK Check if the following BCM fuse or fusible link are blown. Is the fuse or fusible link blown? YES >> Replace the blown fuse or fusible link after repairing the affected circuit. NO >> GO TO 2 2. CHECK POWER SUPPLY CIRCUIT 1. ...

    Sunglasses holder
    To open the sunglasses holder, push and release. Only store one pair of sunglasses in the holder. WARNING Keep the sunglasses holder closed while driving to prevent an accident. CAUTION ● Do not use for anything other than sunglasses. ● Do not leave sunglasses in the sunglass ...