Nissan Altima 2007-2012 Service Manual: Steering switch (sedan)
Description
When one of the steering wheel audio control switches is pushed, the resistance in steering switch circuit changes depending on which button is pushed.
Diagnosis Procedure
WITH BLUETOOTH
1.CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect Bluetooth control unit connector B126 and spiral cable connector M30.
3. Check continuity between Bluetooth control unit connector B126 (A) terminals and spiral cable connector M30 (B) terminals.
4. Check continuity between Bluetooth control unit B126 (A) and ground.
Are the continuity test results as specified? YES >> GO TO 2
NO >> Repair harness.
2.CHECK HARNESS
1. Disconnect audio unit connector.
2. Check continuity between audio unit connector M43 (A) terminals and Bluetooth control unit connector B126 (B) terminals.
Are the continuity test results as specified? YES >> GO TO 3
NO >> Repair harness.
3.SPIRAL CABLE CHECK
1. Disconnect spiral cable connector M88.
2. Check continuity between spiral cable harness connector M30 and M88.
Are the continuity test results as specified? YES >> GO TO 4
NO >> Replace spiral cable. Refer to SR-8, "Removal and Installation".
4.CHECK STEERING SWITCH
Check steering switch. Refer to AV-146, "Component Inspection".
Does the steering switch pass inspection? YES >> Replace Bluetooth control unit. Refer to AV-235, "Removal and Installation - Sedan" NO >> Replace steering switch. Refer to AV-225, "Removal and Installation".
WITHOUT BLUETOOTH
1.CHECK STEERING SWITCH
Check steering switch. Refer to AV-146, "Component Inspection".
Does the steering switch pass inspection? YES >> GO TO 2
NO >> Replace steering switch. Refer to AV-225, "Removal and Installation".
2.CHECK HARNESS
1. Turn ignition switch OFF.
2. Disconnect audio unit connector M43 and spiral cable connector M30.
3. Check continuity between spiral cable harness connector M30 (B) and audio unit harness connector M43 (A).
4. Check continuity between audio unit connector M43 (A) and ground.
Are the continuity test results as specified? YES >> GO TO 3
NO >> Repair harness.
3.SPIRAL CABLE CHECK
1. Disconnect spiral cable connector M88.
2. Check continuity between spiral cable harness connector M30 and M88.
Are the continuity test results as specified? YES >> Inspection End.
NO >> Replace spiral cable. Refer to SR-8, "Removal and Installation".
Component Inspection
WITH BLUETOOTH
Measure the resistance between the steering switch connector terminals 14 to 17 and 15 to 17.
Standard
WITHOUT BLUETOOTH
Measure the resistance between the steering switch connector terminals 14 to 17 and 15 to 17.
Standard
Steering switch (coupe)
Description When one of the steering wheel audio control switches is pushed, the resistance in the steering switch circuit changes depending on which button is pushed. Diagnosis Procedure WITH ...Other materials:
P0139, P0159 HO2S2
Description
The heated oxygen sensor 2, after three way catalyst (manifold),
monitors the oxygen level in the exhaust gas on each bank.
Even if switching characteristics of the air fuel ratio (A/F) sensor 1
are shifted, the air-fuel ratio is controlled to stoichiometric, by the signal
from th ...
Instrument panel
1. Instrument brightness control/Trip computer
reset switch
2. Vents
3. Headlight/fog light (if so equipped)/turn
signal switch
4. Driver supplemental air bag/horn
5. Meters and gauges
6. Paddle shift controls (if so equipped)
7. Windshield wiper/washer switch
8. Hazard warning flasher ...
Insufficient heating
Component Function Check
SYMPTOM: Insufficient heating
INSPECTION FLOW
1. CONFIRM SYMPTOM BY PERFORMING OPERATION CHECK - TEMPERATURE INCREASE
1. Turn temperature control dial clockwise to maximum heat.
2. Check for hot air at discharge air outlets.
Can a symptom be duplicated?
YES >&g ...