Nissan Altima 2007-2012 Service Manual: C1708 - c1711 data from transmitter not being received
Description
Tire pressure data for one or more transmitters is not being received by the BCM.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does DATA MONITOR ITEM display tire pressure as normal without any warning lamp? YES >> Inspection End.
NO >> Refer to WT-14, "Diagnosis Procedure".
Diagnosis Procedure
MALFUNCTION CODE NO. 21, 22, 23 OR 24 (DTC C1708, C1709, C1710 OR C1711)
1.CHECK BCM
Drive for several minutes. Check all tire pressures with CONSULT-III.
Are all tire pressures displayed as 0 kPa? YES >> GO TO 2
NO >> GO TO 3
2.CHECK TIRE PRESSURE RECEIVER CONNECTOR
Check tire pressure receiver connector for damage or loose connections.
Is tire pressure receiver connector damaged or loose? YES >> Repair or replace tire pressure receiver connector.
NO >> Replace BCM, then GO TO 3. Refer to BCS-96, "Removal and Installation".
3.PERFORM ID REGISTRATION
Carry out ID registration of all transmitters. Refer to WT-6, "ID Registration Procedure".
Is there a tire that cannot register ID? YES >> Replace malfunctioning transmitter, then GO TO 5. Refer to WT-68, "Removal and Installation".
NO >> GO TO 4
4.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
2. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does “DATA MONITOR ITEM” display tire pressure as normal without any warning lamp? YES >> Inspection End.
NO >> GO TO 5
5.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does “DATA MONITOR ITEM” display tire pressure as normal without any warning lamp? YES >> Inspection End.
NO >> Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. Refer to WT-5, "Preliminary Check".
C1712 - C1715, C1720 - C1723, C1724 -C1727 Transmitter malfunction
Description One or more transmitters are malfunctioning internally. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.DRIVE VEHICLE 1. Drive at a speed of 40 km/h (25 MPH) or more f ...Other materials:
B210B starter control relay
Description
Starter control relay, integrated in IPDM E/R, permits the starter relay
operation when in N or P position and
the steering is locked or unlocked. It is installed in parallel with the starter
relay.
DTC Logic
DTC DETECTION LOGIC
NOTE:
• If DTC B210B is displayed with DTC U10 ...
B2601 shift position
Description
BCM confirms the shift position with the following 2 signals.
• CVT selector lever
• P position signal from IPDM E/R (CAN)
DTC Logic
DTC DETECTION LOGIC
NOTE:
• If DTC B2601 is displayed with DTC U1000, first perform the trouble diagnosis
for DTC U1000. Refer to
SEC-4 ...
B2612 steering status
Description
There are 2 switches in the electronic steering column lock. IPDM E/R
compares those 2 switches conditions
to judge the present steering status and transmit the result to BCM via CAN
communication.
DTC Logic
DTC DETECTION LOGIC
NOTE:
• If DTC B2612 is displayed with DTC U10 ...