Nissan Altima 2007-2012 Service Manual: Door key cylinder switch

Description

Main power window and door lock/unlock switch detects condition of the door key cylinder and transmits to BCM as the LOCK or UNLOCK signals.

Component Function Check

1. CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL

Check (“KEY CYL LK-SW”, “KEY CYL UN-SW”) in “DATA MONITOR” mode for “POWER DOOR LOCK SYSTEM” with CONSULT-III. Refer to BCS-19, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)".

Is the inspection result normal? YES >> Key cylinder switch is OK.

NO >> Refer to PWC-214, "Diagnosis Procedure".

Diagnosis Procedure

1. CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL

1. Turn ignition switch ON.

2. Check voltage between main power window and door lock/ unlock switch connector and ground.

Is the measurement value within the specification? YES >> Replace main power window and door lock/unlock switch. After that, refer to PWC-199, "POWER WINDOW MAIN SWITCH : Special Repair Requirement".

NO >> GO TO 2

2. CHECK DOOR KEY CYLINDER SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect main power window and door lock/unlock switch and door lock assembly LH (key cylinder switch).

3. Check continuity between main power window and door lock/ unlock switch connector (A) and door lock assembly LH (key cylinder switch) connector (B).

4. Check continuity between main power window and door lock/unlock switch connector (A) and ground.

Is the inspection result normal? YES >> GO TO 3

NO >> Repair or replace harness.

3. CHECK DOOR KEY CYLINDER SWITCH GROUND CIRCUIT

Check continuity between door lock assembly LH (key cylinder switch) connector and ground.

Is the inspection result normal? YES >> GO TO 4

NO >> Repair or replace harness.

4. CHECK DOOR KEY CYLINDER SWITCH

Check door key cylinder switch.

Refer to PWC-215, "Component Inspection".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Replace door lock assembly LH (door key cylinder switch). After that, refer to PWC-216, "Special Repair Requirement".

Component Inspection

1. CHECK DOOR KEY CYLINDER SWITCH

Check door lock assembly LH (key cylinder switch).

Is the inspection result normal? YES >> Key cylinder switch is OK.

NO >> Replace door lock assembly LH (key cylinder switch). After that, refer to PWC-216, "Special Repair Requirement".

Special Repair Requirement

1. PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure.

Refer to PWC-190, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special Repair Requirement".

Is the inspection result normal? YES >> Inspection End.

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

    Door switch
    Description Detects door open/close condition and transmits the signal to BCM. Component Function Check 1. CHECK DOOR SWITCH INPUT SIGNAL Check (“DOOR SW-DR” and “DOOR SW-AS”) in “DATA ...

    Power window serial link
    ...

    Other materials:

    Precaution
    Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and front ...

    NISSAN vehicle immobilizer system
    The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of a registered key. Never leave these keys in the vehicle. FCC Notice: For USA: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This devic ...

    Power steering fluid
    Inspection FLUID LEVEL • Check fluid level with engine stopped. • Make sure that fluid level is between MIN and MAX. • Fluid levels at HOT (A) and COLD (B) are different. Do not confuse them. CAUTION: • The fluid level should not exceed the MAX line. Excessive fluid will caus ...