Nissan Altima 2007-2012 Service Manual: Driver side

Description

Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch.

Component Function Check

1. CHECK POWER WINDOW MOTOR CIRCUIT

Does power window motor LH operate with operating main power window and door lock/unlock switch? Is the inspection result normal? YES >> Power window motor LH is OK.

NO >> Refer to PWC-202, "DRIVER SIDE : Diagnosis Procedure".

Diagnosis Procedure

Power Window Motor LH Circuit Check

1. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OUTPUT SIGNAL

1. Disconnect power window motor LH.

2. Turn ignition switch ON.

3. Check voltage between power window motor LH connector and ground.

Is the measurement value within the specification? YES >> GO TO 2

NO >> Replace main power window and door lock/unlock switch. Refer to PWC-291, "Removal and Installation". After that, refer to PWC-199, "POWER WINDOW MAIN SWITCH : Special Repair Requirement".

2. CHECK HARNESS CONTINUITY

1. Turn ignition switch OFF.

2. Disconnect main power window and door lock/unlock switch and power window motor LH.

3. Check continuity between main power window and door lock/ unlock switch connector (A) and power window motor connector LH (B).

4. Check continuity between main power window and door lock/unlock switch connector (A) and ground.

Is the inspection result normal? YES >> GO TO 3

NO >> Repair or replace harness.

3. CHECK POWER WINDOW MOTOR

Check power window motor LH.

Refer to PWC-203, "DRIVER SIDE : Component Inspection".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Replace power window motor LH. Refer to GW-19, "Removal and Installation". After that, refer to PWC-203, "DRIVER SIDE : Special Repair Requirement".

Component Inspection

COMPONENT INSPECTION

1. CHECK POWER WINDOW MOTOR LH

Does motor operate by connecting the battery voltage directly to power window motor?

Is the inspection result normal? YES >> Power window motor LH is OK.

NO >> Replace power window motor LH. Refer to GW-19, "Removal and Installation". After that, refer to PWC-203, "DRIVER SIDE : Special Repair Requirement".

Special Repair Requirement

1. PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure.

Refer to PWC-190, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".

Is the inspection result normal? YES >> GO TO 2

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

2. CHECK ANTI-PINCH OPERATION

Check anti-pinch operation.

Refer to PWC-190, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".

Is the inspection result normal? YES >> Inspection End.

NO >> Refer to PWC-206, "DRIVER SIDE : Component Function Check".

    Passenger side
     Description Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch or power window and door lock/unlock switch RH. Component Function Check 1. ...

    Other materials:

    When reading the manual
    This manual includes information for all features and equipment available on this model. Features and equipment in your vehicle may vary depending on model, trim level, options selected, order, date of production, region or availability. Therefore, you may find information about features or eq ...

    Common ITEM
    Diagnosis Description BCM CONSULT-III FUNCTION CONSULT-III performs the following functions via CAN communication with BCM. SYSTEM APPLICATION BCM can perform the following functions for each system. NOTE: It can perform the diagnosis modes except the following for all sub system selecti ...

    NISSAN Intelligent Key® Without Door and Trunk Request Switches
    WARNING ● Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should contact the electric medical equipment manufacturer for the possible influences before use. ● The Intelligent Key transmits radio waves when the buttons are pressed. The F ...