Nissan Altima 2007-2012 Service Manual: Driver side

Description

Door glass moves UP/DOWN by receiving the signal from power window main switch.

Component Function Check

1. CHECK POWER WINDOW MOTOR CIRCUIT

Does front power window motor LH operate with operating main power window and door lock/unlock switch? Is the inspection result normal? YES >> Front power window motor LH is OK.

NO >> Refer to PWC-313, "DRIVER SIDE : Diagnosis Procedure".

Diagnosis Procedure

Front Power Window Motor LH Circuit Check

1. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OUTPUT SIGNAL

1. Disconnect front power window motor LH.

2. Turn ignition switch ON.

3. Check voltage between front power window motor LH connector and ground.

Is the measurement value within the specification? YES >> GO TO 2

NO >> Replace main power window and door lock/unlock switch. Refer to PWC-411, "Removal and Installation". After that, refer to PWC-314, "DRIVER SIDE : Special Repair Requirement".

2. CHECK HARNESS CONTINUITY

1. Turn ignition switch OFF.

2. Disconnect main power window and door lock/unlock switch and front power window motor LH.

3. Check continuity between main power window and door lock/ unlock switch connector (A) and front power window motor connector LH (B).

4. Check continuity between main power window and door lock/unlock switch connector (A) and ground.

Is the inspection result normal? YES >> GO TO 3

NO >> Repair or replace harness.

3. CHECK POWER WINDOW MOTOR

Check front power window motor LH.

Refer to PWC-314, "DRIVER SIDE : Component Inspection".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Replace power window motor LH. Refer to GW-19, "Removal and Installation". After that, refer to PWC-314, "DRIVER SIDE : Special Repair Requirement".

Component Inspection

1. CHECK FRONT POWER WINDOW MOTOR LH

Does motor operate by connecting the battery voltage directly to power window motor?

Is the inspection result normal? YES >> Front power window motor LH is OK.

NO >> Replace front power window motor LH. Refer to GW-19, "Removal and Installation". After that, refer to PWC-314, "DRIVER SIDE : Special Repair Requirement".

Special Repair Requirement

1. PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure.

Refer to PWC-295, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".

Is the inspection result normal? YES >> GO TO 2

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

2. CHECK ANTI-PINCH OPERATION

Check anti-pinch operation.

Refer to PWC-295, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".

Is the inspection result normal? YES >> Inspection End.

NO >> Refer to PWC-320, "DRIVER SIDE : Component Function Check".

    Passenger side
    Description Door glass moves UP/DOWN by receiving the signal from main power window and door lock/unlock switch or power window and door lock/unlock switch RH. Component Function Check 1. CHECK ...

    Other materials:

    Mixture ratio self-learning value clear
    Description This describes show to erase the mixture ratio self-learning value. For the actual procedure, follow the instructions in “Diagnosis Procedure”. Special Repair Requirement 1.START 1. Start engine and warm it up to normal operating temperature. 2. Select “SELF-LEARNING CO ...

    P0725 engine speed signal
    Description The engine speed signal is sent from the ECM to the TCM by CAN communication line. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE CAUTION: Always drive vehicle at a safe speed. NOTE: If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn i ...

    Precaution
    Supplemental Restraint System (SRS) "AIR B AG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver and fron ...