Nissan Altima 2007-2012 Service Manual: Headlining
Exploded View
1. Room/Map lamp assembly
2. Mirror harness cover
3. Sunvisor holder
4. Sunvisor
5. Sunvisor cover
6. Headlining assembly (without sunroof)
7. Headlining assembly (with sunroof)
8. Rear assist grip
9. Front assist grip
10. Sunroof clip
A. Metal clip
B. Dual lock fastener
C. Clip C101
Removal and Installation
CAUTION: • Disconnect the negative and positive battery terminals.
• Be careful not to bend headlining during removal or installation.
REMOVAL
1. Disconnect the negative and positive battery terminals.
2. Remove front pillar finisher (RH/LH). Refer to INT-36, "Removal and Installation".
3. Disconnect headlining harness and antenna feeder connectors.
4. Remove center pillar upper and rear pillar finishers. Refer to INT-36, "Removal and Installation".
5. Disconnect antenna amplifier and rear window defogger connectors.
6. Release the molded clip, then remove front and rear assist grips.
7. Remove the sunvisor covers and screws, and then remove sunvisors (RH/LH).
• If equipped, disconnect vanity mirror illumination harness connector.
8. Insert a suitable thin tool into the sunvisor holder notch and press in to release the locking tab.
• Rotate sunvisor holder 90 degrees and pull away from headlining to remove.
9. Remove map lamp assembly.
• For sunroof equipped vehicles: Release the pawls and lower map lamp assembly away from headliner.
Disconnect the map lamp and sunroof switch connectors, then remove the map lamp assembly.
• For non-sunroof equipped vehicles: The map lamp assembly is an integral part of the headlining, and repaired only as an assembly.
10. For sunroof equipped vehicles, use a suitable tool to release dual lock fastener(s) around the sunroof opening and release the sunroof clip.
11. Release the three hidden clips near the rear edge of headliner using a suitable clip removal tool.
12. Place gear selector lever to D position, then recline the front seats to the fully reclined position.
13. Drop headlining down and carefully rotate into position. Remove headlining through rear door opening.
CAUTION: • When removing, two workers are required. (one for each front and rear of headlining) • Cover center console finisher upper surface with a shop cloth to prevent damage.
14. The following components are integral to the headliner and are repaired only as an assembly: • Personal lamp (LH/RH).
• Roof harness assembly.
• Antenna feeder assembly.
INSTALLATION
Installation is in the reverse order of removal.
Floor trim
Exploded View
1. Spacer (RH)
2. Spacer (LH)
3. Floor mat hook
4. Floor carpet
5. Harness clamp
Removal and Installation
REMOVAL
1. Remove front seat (RH/LH) and rear seat cushion. Refer ...
Trunk room trim & trunk lid finisher
Exploded View
TRUNK ROOM TRIM
1. Trunk lid finisher
2. Trunk lid rubber bumper
3. Trunk net rear
4. Trunk rear finisher
5. Trunk side finisher (RH)
6. Trunk floor carpet
7. Spare tire cover
...
Other materials:
Capacities and recommended fuel/lubricants
The following are approximate capacities. The actual refill capacities may
be slightly different. When refilling, follow the procedure
described in the “Maintenance and do-it-yourself” section to determine the
proper refill capacity.
*1: For further details, see “Engine oil and oil fil ...
List of voice commands
When you press and release the
button on
the steering wheel, you can choose from the
commands on the Main Menu. The following
pages describe these commands and the commands
in each sub-menu.
Remember to wait for the tone before
speaking.
After the main menu, you can say “Help” to h ...
The light reminder warning does not sound
Description
Light reminder warning does not sound even though headlamp is illuminated.
Diagnosis Procedure
1. CHECK COMBINATION SWITCH (LIGHT SWITCH) OPERATION
Check that the headlamps operate normally by operating the combination switch
(light switch).
Do they operate normally?
YES > ...