Nissan Altima 2007-2012 Service Manual: Inspection and adjustment
Description & Conditions
DESCRIPTION
The purpose of the operational check is to confirm that the system operates properly.
CONDITIONS: • Engine running and at normal operation temperature.
Operational Check
STEP 1: Check Blower
1. Turn blower control dial clockwise, blower should operate on low speed.
2. Continue turning blower control dial clockwise, and continue checking blower speeds until all speeds are checked.
3. Leave blower on HI speed.
If NG, go to HAC-127, "Diagnosis Procedure".
If OK, continue with next check.
STEP 2: Check Discharge Air
1. Press each mode switch and press DEF (
) switch.
2. Each mode position indicator should illuminate.
3. Confirm that discharge air comes out according to the air distribution table. Refer to HAC-107, "System Description".
NOTE:
Confirm that the compressor clutch is engaged (audio or visual inspection) and
intake door is in the FRE
( ) position when the DEF (
) is selected.
Intake door position is checked in the next step.
If NG, go to HAC-124, "Diagnosis Procedure".
If OK, continue with next check.
STEP 3: Check Recirculation
1. Press REC ( ) switch.
Recirculation indicator should illuminate.
2. Press REC ( ) switch a second
time.
3. Listen for intake door position change (you should hear blower sound change slightly).
If NG, go toHAC-124, "Diagnosis Procedure".
If OK, continue with next check.
STEP 4: Check Temperature Decrease
1. Turn the temperature dial counterclockwise to maximum cold.
2. Check for cold air at discharge air outlets.
If NG, go to HAC-122, "Diagnosis Procedure".
If OK, continue with next check.
STEP 5: Check Temperature Increase
1. Turn the temperature dial clockwise to maximum heat.
2. Check for hot air at discharge air outlets.
If NG, go toHAC-122, "Diagnosis Procedure".
If OK, continue with next check.
STEP 6: Check Air Conditioner Switch (if equipped)
1. Turn blower control dial to the desired position and push the A/C switch to turn ON the air conditioner
2. Confirm that the A/C indicator illuminates and that the compressor clutch engages (audio or visual inspection).
If NG, go to HAC-135, "Diagnosis Procedure", then if necessary, HAC-131, "Diagnosis Procedure".
If OK, listen to customer complaint (get detailed information about the conditions and environment when the symptom occurs). Verify the symptom and refer to HAC-155, "Symptom Matrix Chart".
Diagnosis and repair workflow
Work Flow
DETAILED FLOW
1.LISTEN TO CUSTOMER COMPLAINT
Listen to customer complaint. Get detailed information about the conditions
and environment when the symptom
occurs.
>> GO TO 2
2 ...
Other materials:
How to select piston and bearing
DESCRIPTION
*For the service parts, the grade for fitting cannot be selected between a
piston pin and a connecting rod.
(Only 0 grade is available.) The information at the shipment from the plant is
described as a reference.
• The identification grade stamped on each part is the grade ...
P0444, P0445 Evap canister purge volume control solenoid valve
Description
The EVAP canister purge volume control solenoid valve is used to
control the flow rate of fuel vapor from the EVAP canister. The EVAP
canister purge volume control solenoid valve is moved by ON/OFF
pulses from the ECM. The longer the ON pulse, the greater the
amount of fuel vapor th ...
Oil cooler
Removal and Installation
1. Oil pressure switch
2. Oil cooler
3. Gasket
4. Water hose (outlet)
5. Water hose (inlet)
A. To water control valve housing
B. To heater pipe assembly
C. Hose clamp
D. Clip
WARNING:
Be careful not to get burned, engine coolant and engine oil may be hot.
CAUTI ...