Nissan Altima 2007-2012 Service Manual: P1715 Input speed sensor (primary speed sensor)
Description
ECM receives primary speed sensor signal from TCM via the CAN communication line. ECM uses this signal for engine control.
DTC Logic
DTC DETECTION LOGIC
NOTE: • If DTC P1715 is displayed with DTC UXXXX first perform the trouble diagnosis for DTC UXXXX. Refer to EC-1179, "DTC Logic".
• If DTC P1715 is displayed with DTC P0335, first perform the trouble diagnosis for DTC P0335. Refer to EC-1292, "DTC Logic".
• If DTC P1715 is displayed with DTC P0340, P0345, first perform the trouble diagnosis for DTC P0340, P0345. Refer to EC-1296, "DTC Logic".
• If DTC P1715 is displayed with DTC P0605, first perform the trouble diagnosis for DTC P0605. Refer to EC-1376, "DTC Logic".
• If DTC P1715 is displayed with DTC P0607, first perform the trouble diagnosis for DTC P0607. Refer to EC-1378, "DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine.
2. Drive vehicle at a speed of more than 50 km/h (31 MPH) for at least 5 seconds.
3. Check 1st trip DTC.
Is 1st trip DTC detected? YES >> Go to EC-1424, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis Procedure
1.CHECK DTC WITH TCM
Check DTC with TCM. Refer to TM-221, "DTC Index".
Is the inspection result normal? YES >> GO TO 2.
NO >> Perform trouble shooting relevant to DTC indicated.
2.REPLACE TCM
Replace TCM. Refer to TM-254, "Removal and Installation".
>> INSPECTION END
P1700 CVT Control system
Description
This DTC is displayed with other DTC regarding TCM. Perform the trouble
diagnosis for corresponding DTC.
Refer to EC-1555, "DTC Index". When this DTC is detected, the ASCD ...
P1720 VSS
Description
ECM receives two vehicle speed signals via the CAN communication line. One is
sent from “ABS actuator and
electric unit (control unit)” via the combination meter, and the other is ...
Other materials:
B2560 starter control relay
Description
Starter control relay, integrated in IPDM E/R, permits the starter relay
operation when in N or P position and
the steering is locked or unlocked. It is installed in parallel with the starter
relay.
DTC Logic
DTC DETECTION LOGIC
NOTE:
• If DTC B2560 is displayed with DTC U1 ...
Rear parcel shelf finisher
Exploded View
1. Seatback release escutcheon
2. Seatback release cover
3. Child anchor cover
4. Seatback latch cover
5. Rear parcel shelf finisher
6. High mounted stop lamp (if equipped)
A. Clip C205
Removal and Installation
REMOVAL
1. Release seatback latch RH/LH, then fold both r ...
P0128 Thermostat function
DTC Logic
DTC DETECTION LOGIC
NOTE:
If DTC P0128 is displayed with DTC P0300, P0301, P0302, P0303, P0304, P0305 or
P0306, first perform
the trouble diagnosis for DTC P0300, P0301, P0302, P0303, P0304, P0305, P0306.
Refer to EC-1283,
"DTC Logic".
Engine coolant temperature has n ...