Nissan Altima 2007-2012 Service Manual: P1801 Vias control solenoid valve 2

Description

The VIAS control solenoid valve 2 cuts the intake manifold vacuum signal for power valve 2 control. It responds to ON/OFF signals from the ECM. When the solenoid is OFF, the vacuum signal from the intake manifold is cut. When the ECM sends an ON signal the coil pulls the plunger downward and sends the vacuum signal to the power valve actuator 2.

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.CONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION: Before performing the following procedure, confirm battery voltage is more than 11 V at idle.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

1. Start engine and let it idle for at least 5 seconds.

2. Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Go to EC-1431, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK VIAS CONTROL SOLENOID VALVE 2 POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect VIAS control solenoid valve 2 harness connector.

3. Turn ignition switch ON.

4. Check the voltage between VIAS control solenoid valve 2 harness connector and ground.

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair open circuit, short to ground or short to power in harness or connectors.

2.CHECK VIAS CONTROL SOLENOID VALVE 2 OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between VIAS control solenoid valve 2 harness connector and ECM harness connector.

4. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair open circuit, short to ground or short to power in harness or connectors.

3.CHECK VIAS CONTROL SOLENOID VALVE 2

Refer to EC-1432, "Component Inspection".

Is the inspection result normal? YES >> GO TO 4.

NO >> Replace VIAS control solenoid valve 2.

4.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident".

>> INSPECTION END

Component Inspection

1.CHECK VIAS CONTROL SOLENOID VALVE 2

1. Turn ignition switch OFF.

2. Reconnect all harness connectors disconnected.

3. Disconnect vacuum hoses connected to VIAS control solenoid valve 2.

4. Turn ignition switch ON.

5. Select “VIAS S/V-2” in “ACTIVE TEST” mode with CONSULT-III.

6. Check air passage continuity and operation delay time under the following conditions.

1. Turn ignition switch OFF.

2. Disconnect VIAS control solenoid valve 2 harness connector.

3. Disconnect vacuum hoses connected to VIAS volume control solenoid valve 2.

4. Check air passage continuity and operation delay time under the following conditions.

Is the inspection result normal? YES >> INSPECTION END

NO >> Replace VIAS control solenoid valve 2

    P1800 Vias control solenoid valve 1
    Description The VIAS control solenoid valve 1 cuts the intake manifold vacuum signal for power valve 1 control. It responds to ON/OFF signals from the ECM. When the solenoid is OFF, the vacuum s ...

    P1805 Brake switch
    Description Brake switch signal is applied to the ECM via the stop lamp switch when the brake pedal is depressed. This signal is used mainly to decrease the engine speed when the vehicle is being ...

    Other materials:

    Additional service when removing battery negative terminal
    Description Initial setting is necessary when battery terminal is removed. CAUTION: The following specified operations are not performed under the non-initialized condition. • Auto-up operation • Anti-pinch function • Retained power operation Special Repair Requirement INITIALIZ ...

    Diagnosis system (audio unit)
    Diagnosis Description Self-diagnosis mode can check the following items. • Audio unit hardware/software versions • Continuity of each speaker channel • Continuity of each audio unit switch OPERATION PROCEDURE 1. Turn ignition switch to the ACC position. 2. Turn the audio unit off. ...

    LATCH (Lower Anchors and Tethers for CHildren) System
    LATCH system anchor locat Your vehicle is equipped with special anchor points that are used with LATCH (Lower Anchors and Tethers for CHildren) system compatible child restraints. This system may also be referred to as the ISOFIX or ISOFIX compatible system. With this system, you do not ha ...