Nissan Altima 2007-2012 Service Manual: B2014 chain of strg-immu
Description
BCM performs the ID verification with the steering lock unit to release the steering. BCM starts the communication with the steering lock unit when Intelligent Key is carried into the passenger compartment and the pushbutton ignition switch is pressed.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Lock steering.
2. Press the push-button ignition switch.
3. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected? YES >> Refer to SEC-39, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis Procedure
1.CHECK STEERING LOCK UNIT POWER SUPPLY
1. Turn ignition switch OFF.
2. Disconnect steering lock unit harness connector.
3. Check voltage between steering lock unit harness connector and ground while turning ignition switch from OFF to ACC.
Is the inspection result normal? YES >> GO TO 3
NO >> GO TO 2
2.CHECK STEERING LOCK UNIT POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM harness connector.
3. Check continuity between steering lock unit harness connector M32 (A) terminal 7 and BCM harness connector M19 (B) terminal 94.
4. Check continuity between steering lock unit harness connector M32 (A) terminal 7 and ground.
Is the inspection result normal? YES >> GO TO 6
NO >> Repair harness or connector.
3.CHECK STEERING LOCK UNIT GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Check continuity between steering lock unit and ground.
Is the inspection result normal? YES >> GO TO 4
NO >> Repair harness or connector.
4.CHECK STEERING LOCK UNIT COMMUNICATION SIGNAL
1. Connect steering lock unit harness connector.
2. Using an oscilloscope, read voltage signal between steering lock unit harness connector and ground.
Steering is locked : Opening the door when ignition switch is ON to OFF.
Steering is unlocked : Ignition switch is OFF to ACC.
Is the inspection result normal? YES >> Replace steering lock unit.
NO >> GO TO 5
5.CHECK STEERING LOCK UNIT COMMUNICATION CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect BCM harness connector.
3. Check continuity between BCM harness connector M19 (A) terminal 99 and steering lock unit harness connector M32 (B) terminal 2.
4. Check continuity between BCM harness connector M19 (A) terminal 99 and ground.
Is the inspection result normal? YES >> GO TO 6
NO >> Repair harness or connector.
6.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "Intermittent Incident".
>> Inspection End.
B2013 ID discord, immu-strg
Description
BCM performs the ID verification with the steering lock unit and releases the
steering lock if both BCM and
steering lock unit ID are same. BCM starts the communication with the steer ...
B2108 steering lock relay
Description
The steering lock relay ON signal is transmitted to IPDM E/R by BCM via CAN
communication.
IPDM E/R turns the steering lock relay ON and transmits the release of the
steering to B ...
Other materials:
Precaution
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”,
used along
with a front seat belt, helps to reduce the risk or severity of injury to the
dr ...
B2555 stop lamp
Description
BCM detects the stop lamp status and confirms the stop lamp switch ON/OFF
status. BCM confirms the
engine start condition according to the stop lamp switch ON/OFF status.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Depress ...
Front wiper ARMS
Removal and Installation
REMOVAL
1. Turn wiper switch ON to operate wiper motor, and then turn wiper switch
OFF (auto stop).
2. Open hood, remove arm caps, and remove wiper arm nuts.
3. Raise wiper arm, and remove wiper arm from the vehicle.
INSTALLATION
1. Clean up the pivot area as sho ...