Nissan Altima 2007-2012 Service Manual: B2110 PNP/Clutch interlock switch
Description
IPDM E/R confirms the shift position with the following signals.
• Park/neutral position (PNP) switch
• Shift position signal from BCM (CAN)
DTC Logic
DTC DETECTION LOGIC
NOTE: • If DTC B2110 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to SEC-433, "DTC Logic".
• If DTC B2110 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to SEC-434, "DTC Logic".
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn the ignition switch ON under the following conditions and wait for at least 1 second.
- CVT selector lever is in the P or N position
- Do not depress the brake pedal
2. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected? YES >> Refer to SEC-452, "Diagnosis Procedure".
NO >> Inspection End.
Diagnosis Procedure
1.CHECK DTC WITH BCM
Refer to BCS-91, "DTC Index".
Is the inspection result normal? YES >> GO TO 2
NO >> Repair or replace malfunctioning parts.
2.CHECK PNP SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R harness connector.
3. Turn ignition switch ON.
4. Check voltage between IPDM E/R harness connector and ground under following condition.
Is the inspection result normal?
YES >> Replace IPDM E/R. Refer to PCS-48, "Removal and Installation".
NO >> GO TO 3
3.CHECK PNP SWITCH CIRCUIT FOR CONTINUITY
1. Turn ignition switch OFF.
2. Check continuity between IPDM E/R harness connector terminals 72 and 74.
Is the inspection result normal? YES >> GO TO 4
NO >> GO TO 5
4.CHECK PNP SWITCH CIRCUIT FOR SHORT
Check continuity between IPDM E/R harness connector terminals 72, 74 and ground.
Is the inspection result normal? YES >> Replace the IPDM E/R. Refer to PCS-48, "Removal and Installation".
NO >> Repair or replace harness.
5.CHECK PNP SWITCH INPUT SIGNAL CIRCUIT
1. Disconnect PNP switch harness connector.
2. Check continuity between PNP switch and IPDM E/R harness connectors.
3. Check continuity between PNP switch harness connector and ground.
Is the inspection result normal? YES >> Replace PNP switch.
NO >> Repair harness or connector.
Component Inspection
1.CHECK CLUTCH INTERLOCK SWITCH
1. Turn ignition switch OFF.
2. Disconnect clutch interlock switch harness connector.
3. Check continuity between clutch interlock switch under the following conditions.
Is the inspection result normal? YES >> Inspection End.
NO >> Replace clutch interlock switch.
B210F PNP/Clutch interlock switch
Description
IPDM E/R confirms the shift position with the following signals.
• Park/neutral position (PNP) switch
• Shift position signal from BCM (CAN)
DTC Logic
DTC DETECTION LOGIC
NOTE ...
B2190, P1610 nats antenna amp
Description
Performs ID verification through BCM and keyfob when push-button ignition
switch is pressed.
Prohibits the release of steering lock or start of engine when an unregistered
ID of ke ...
Other materials:
P1225 TP Sensor
Description
Electric throttle control actuator consists of throttle control motor,
throttle position sensor, etc. The throttle position sensor responds to
the throttle valve movement.
The throttle position sensor has two sensors. These sensors are a
kind of potentiometer which transform the t ...
Can communication circuit
Diagnosis Procedure
INSPECTION PROCEDURE
1.CONNECTOR INSPECTION
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Disconnect all the unit connectors on CAN communication system.
4. Check terminals and connectors for damage, bend and loose con ...
Front seat
Exploded View
DRIVER'S SEAT
1. Headrest
2. Headrest holder (locked)
3. Headrest holder (free)
4. Seatback board
5. Seatback assembly
6. Slide cover
7. Seat belt buckle
8. Seat harness
9. Seat cushion heater unit
10. Seat cushion
11. Seat trim
12. Front leg covers
13. Seat cushion fr ...