Nissan Altima 2007-2012 Service Manual: C1716 - C1719 Transmitter pressure malfunction
Description
Air pressure data from one or more transmitters is out of range.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does DATA MONITOR ITEM display tire pressure as normal without any warning lamp? YES >> Inspection End.
NO >> Refer to WT-18, "Diagnosis Procedure".
Diagnosis Procedure
MALFUNCTION CODE NO. 35, 36, 37 OR 38 (DTC C1716, C1717, C1718 OR C1719)
1.CHECK ALL TIRE PRESSURES
Check all tire pressures. Refer to WT-70, "Tire".
Are there any tires with pressure of 64 psi or more? YES >> Adjust tire pressure to specified value.
NO >> GO TO 2
2.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters. Refer to WT-6, "ID Registration Procedure".
2. Drive at a speed of 40 km/h (25 MPH) or more for several minutes without stopping.
3. Check all tire pressures with CONSULT-III within 15 minutes after vehicle speed becomes 17 km/h (11 MPH).
Does “DATA MONITOR ITEM” display 64 psi or more? YES >> Replace transmitter. Refer to WT-68, "Removal and Installation". GO TO 3.
NO >> GO TO 3
3.ID REGISTRATION AND VEHICLE DRIVING
1. Carry out ID registration of all transmitters.
2. Drive at a speed of 40 km/h (25 MPH) or more for 3 minutes, and then drive the vehicle at any speed for 10 minutes.
3. Check all tire pressures with CONSULT-III within 5 minutes.
Does “DATA MONITOR ITEM” display tire pressure as normal without any warning lamp? YES >> Inspection End.
NO >> Proceed to the inspection applicable to DTC.
Special Repair Requirement
Perform preliminary check. Refer to WT-5, "Preliminary Check".
C1712 - C1715, C1720 - C1723, C1724 -C1727 Transmitter malfunction
Description
One or more transmitters are malfunctioning internally.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.DRIVE VEHICLE
1. Drive at a speed of 40 km/h (25 MPH) or more f ...
C1729 vehicle speed signal
Description
The vehicle speed signal is not being detected by the BCM.
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.CHECK SELF-DIAGNOSTIC RESULTS
1. On SELECT DIAG MODE, select t ...
Other materials:
Normal operating condition
COMPASS
Description
• The electronic compass is highly protected from changes in most magnetic
fields. However, some large
changes in magnetic fields can affect it. Some examples are (but not limited
to): high tension power lines,
large steel buildings, subways, steel bridges, automatic c ...
Additional service when replacing
control unit
Description
Initial setting is necessary when replacing power window main switch.
CAUTION:
The following specified operations are not performed under the non-initialized
condition.
• Auto-up operation
• Anti-pinch function
• Retained power operation
Special Repair Requirement
INITI ...
Precaution
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER"
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”,
used along
with a front seat belt, helps to reduce the risk or severity of injury to the
dr ...