Nissan Altima 2007-2012 Service Manual: Door key cylinder switch

Description

Power window main switch detects condition of the door key cylinder and transmits to BCM as the LOCK or UNLOCK signals.

Component Function Check

1. CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL

Check (“KEY CYL LK-SW”, “KEY CYL UN-SW”) in “DATA MONITOR” mode for “POWER DOOR LOCK SYSTEM” with CONSULT-III. Refer to BCS-19, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK)".

Is the inspection result normal? YES >> Key cylinder switch is OK.

NO >> Refer to PWC-328, "Diagnosis Procedure".

Diagnosis Procedure

1. CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL

1. Turn ignition switch ON.

2. Check voltage between main power window and door lock/ unlock switch connector and ground.

Is the measurement value within the specification? YES >> Replace main power window and door lock/unlock switch. After that, refer to PWC-307, "POWER WINDOW MAIN SWITCH : Special Repair Requirement".

NO >> GO TO 2

2. CHECK DOOR KEY CYLINDER SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect main power window and door lock/unlock switch and front door lock assembly LH (key cylinder switch).

3. Check continuity between main power window and door lock/ unlock switch connector (A) and front door lock assembly LH (key cylinder switch) connector (B).

4. Check continuity between main power window and door lock/unlock switch connector (A) and ground.

Is the inspection result normal? YES >> GO TO 3

NO >> Repair or replace harness.

3. CHECK DOOR KEY CYLINDER SWITCH GROUND CIRCUIT

Check continuity between front door lock assembly LH (key cylinder switch) connector and ground.

Is the inspection result normal? YES >> GO TO 4

NO >> Repair or replace harness.

4. CHECK DOOR KEY CYLINDER SWITCH

Check door key cylinder switch.

Refer to PWC-329, "Component Inspection".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Replace front door lock assembly LH (door key cylinder switch). After that, refer to PWC-330, "Special Repair Requirement".

Component Inspection

1. CHECK DOOR KEY CYLINDER SWITCH

Check front door lock assembly LH (key cylinder switch).

Is the inspection result normal? YES >> Key cylinder switch is OK.

NO >> Replace front door lock assembly LH (key cylinder switch). After that, refer to PWC-330, "Special Repair Requirement".

Special Repair Requirement

1. PERFORM INITIALIZATION PROCEDURE

Perform initialization procedure.

Refer to PWC-295, "ADDITIONAL SERVICE WHEN REMOVING BATTERY NEGATIVE TERMINAL : Special Repair Requirement".

Is the inspection result normal? YES >> Inspection End.

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

    Door switch
    Description Detects door open/close condition and transmits the signal to BCM. Component Function Check 1. CHECK FRONT DOOR SWITCH INPUT SIGNAL Check (“DOOR SW-DR” and “DOOR SW-AS”) in ...

    Other materials:

    P0460 Fuel level sensor
    Description The fuel level sensor is mounted in the fuel level sensor unit. The sensor detects a fuel level in the fuel tank and transmits a signal to the combination meter. The combination meter sends the fuel level sensor signal to the ECM via the CAN communication line. It consists of ...

    Primary speed sensor
    Exploded View 1. CVT assembly 2. O-ring 3. Primary speed sensor Removal and Installation Refer to the figure for removal and installation. CAUTION: • Do not reuse O-ring. • Apply CVT fluid to O-ring. • After installation is complete, check for CVT fluid leakage and CVT fluid ...

    The oil pressure warning lamp does not turn off
    Description The oil pressure warning lamp remains illuminated while the engine is running (normal oil pressure). Diagnosis Procedure 1.CHECK OIL PRESSURE WARNING LAMP Perform IPDM E/R auto active test. Refer to PCS-14, "Diagnosis Description". Is oil pressure warning lamp illumin ...