Nissan Altima 2007-2012 Service Manual: Front seat
DRIVER SIDE
Exploded View
DRIVER'S SEAT
1. Headrest
2. Headrest holder (locked)
3. Headrest holder (free)
4. Seatback board
5. Seatback assembly
6. Slide cover
7. Seat belt buckle
8. Seat harness
9. Seat cushion heater unit
10. Seat cushion
11. Seat trim
12. Front leg covers
13. Seat cushion frame
14. Manual seat lifter lever finisher
15. Manual seat recliner handle
16. Manual seat lifter lever
17. Manual seat outer finisher
18. Seat slide switch
19. Seat reclining switch
20. Power seat outer finisher
21. Seat switch assembly
22. LH seat bracket
23. Front seat finisher
24. Cushion bracket
25. Inner seat cover
26. Seat frame assembly
27. Cushion finishers
28. Rear leg covers
Disassembly and Assembly
SEAT CUSHION TRIM AND PAD
Disassembly
CAUTION: • During installation, the wire harness clips must be reinstalled in the holes they were originally in. Do not add additional clips.
NOTE: If the vehicle has been involved in a collision, the seat must be inspected for damage. Refer to SR-21, "For Side and Rollover Collision".
1. Remove the front seat assembly. Refer to SE-51, "Removal and Installation" 2. Remove the front seat finishers and seat outer finisher.
3. Pull up (A) on the seat cushion trim flap (1).
4. Remove two rear clips retaining the seat cushion trim flap, remove seat cushion assembly.
5. Remove the retainer on the seat cushion frame, then remove the harness connector for the seat heater.
6. After removing the seat cushion trim and pad, remove the hog rings to separate the trim from the pad and seat cushion heater unit.
Assembly
Assembly is in the reverse order of disassembly.
SEATBACK BOARD
Disassembly
CAUTION: • During installation, the wire harness clips must be reinstalled in the holes they were originally in. Do not add additional clips.
NOTE: If the vehicle has been involved in a collision, the seat must be inspected for damage. Refer to SR-21, "For Side and Rollover Collision".
1. Slide the seat to forward position.
2. The seatback board is attached to the seat frame with the following: • 2 top clips (A) (must be replaced) • 2 side hooks (B) • 2 bottom hooks (C)
3. Hold the seatback board as shown and push in the side hooks to release them from the seat back frame.
4. Carefully pull up on the seatback board to release the bottom hooks.
5. Reach in from the bottom of the seatback board to release the top clips. Squeeze the clips at the location shown (A) using suitable tool.
Assembly
Assembly is in the reverse order of disassembly.
PASSENGER SIDE
Exploded View
1. Headrest
2. Headrest holder (locked)
3. Headrest holder (free)
4. Seatback board
5. Seatback assembly
6. Seat cushion assembly
7. Bushing
8. Seat cushion frame assembly
9. Front leg covers
10. Cushion bracket
11. Seat frame assembly
12. Seat harness
13. Seat belt buckle
14. Inner finisher
15. Outer finisher
16. Seat cushion supporter
17. Recliner mechanism
18. Finisher
19. Cushion finishers
20. Rear leg covers
Disassembly
SEAT CUSHION TRIM AND PAD
Disassembly
CAUTION: • During installation, the wire harness clips must be reinstalled in the holes they were originally in. Do not add additional clips.
NOTE: If the vehicle has been involved in a collision, the seat must be inspected for damage. Refer to SR-21, "For Side and Rollover Collision".
1. Remove the front seat assembly. Refer to SE-51, "Removal and Installation" 2. Remove the front seat finishers and seat outer finisher.
3. Pull up (A) on the seat cushion trim flap (1).
4. Remove two rear clips retaining the seat cushion trim flap, remove seat cushion assembly.
5. Remove the retainer on the seat cushion frame, then remove the harness connector for the seat heater.
6. After removing the seat cushion trim and pad, remove the hog rings to separate the trim from the pad and seat cushion heater unit.
Assembly
Assembly is in the reverse order of disassembly.
SEATBACK BOARD
Disassembly
CAUTION: • During installation, the wire harness clips must be reinstalled in the holes they were originally in. Do not add additional clips.
NOTE: If the vehicle has been involved in a collision, the seat must be inspected for damage. Refer to SR-21, "For Side and Rollover Collision".
1. Slide the seat to forward position.
2. The seatback board is attached to the seat frame with the following: • 2 top clips (A) (must be replaced) • 2 side hooks (B) • 2 bottom hooks (C)
3. Hold the seatback board as shown and push in the side hooks to release them from the seat back frame.
4. Carefully pull up on the seatback board to release the bottom hooks.
5. Reach in from the bottom of the seatback board to release the top clips. Squeeze the clips at the location shown (A) using suitable tool.
Assembly
Assembly is in the reverse order of disassembly.
Rear seat
ARMREST
Exploded View
1. Right seatback trim and pad
2. Armrest
3. Armrest trim panel
Disassembly and Assembly
Disassembly
1. Fold left seatback forward.
2. Remove the armrest trim panel. ...
Other materials:
Door key cylinder switch
Description
Power window main switch detects condition of the door key cylinder and
transmits to BCM as the LOCK or
UNLOCK signals.
Component Function Check
1. CHECK DOOR KEY CYLINDER SWITCH INPUT SIGNAL
Check (“KEY CYL LK-SW”, “KEY CYL UN-SW”) in “DATA MONITOR” mode for “POWER ...
P0117, P0118 ECT sensor
Description
The engine coolant temperature sensor is used to detect the engine
coolant temperature. The sensor modifies a voltage signal from the
ECM. The modified signal returns to the ECM as the engine coolant
temperature input. The sensor uses a thermistor which is sensitive to
the change i ...
Bluetooth® streaming audio without Navigation System (Type A) (if so
equipped)
If you have a compatible Bluetooth® audio device
that is capable of playing audio files, the
device can be connected to the vehicle’s audio
system so that the audio files on the device play
through the vehicle’s speakers.
Connecting Bluetooth® audio
To connect your Bluetooth® audio de ...