Nissan Altima 2007-2012 Service Manual: Fuel level sensor unit, fuel filter and fuel pump assembly
Exploded View
1. Lock ring
2. Fuel level sensor unit, fuel filter and fuel pump assembly
3. O-ring
4. Fuel Tank
Removal and Installation
REMOVAL
WARNING: Read “General Precautions” before working on the fuel system.
Refer to GI-28, "General Precautions".
1. Unscrew the fuel filler cap to release the pressure inside the fuel tank.
2. Release the fuel pressure from the fuel lines. Refer to EC-550, "Inspection" (QR25DE For California), EC- 1038, "Inspection" (QR25DE Except For California), EC-1579, "Inspection" (VQ35DE).
3. Disconnect the battery negative terminal.
4. Remove the rear seat bottom. Refer to SE-25, "Removal and Installation".
5. Turn the four retainers 90° in a clockwise direction and remove the fuel pump inspection hole cover.
6. Disconnect the fuel level sensor, fuel filter, and fuel pump assembly electrical connector, EVAP hose quick connector, and the fuel feed hose quick connector from the fuel level sensor unit, fuel filter, and fuel pump assembly.
Remove the quick connector as follows: • Hold the sides of the connector, push in tabs and pull out the tube.
• If the connector and the tube are stuck together, push and pull several times until they start to move. Then disconnect them by pulling.
CAUTION: • The tube can be removed when the tabs are completely depressed. Do not twist it more than necessary.
• Do not use any tools to remove the quick connector.
• Keep the resin tube away from heat. Be especially careful when welding near the tube.
• Prevent acid liquid such as battery electrolyte, etc. from getting on the resin tube.
• Do not bend or twist the tube during installation and removal.
• Only when the tube is replaced, remove the remaining retainer on the tube or fuel level sensor, fuel filter, and fuel pump assembly.
• When the tube or fuel level sensor, fuel filter, and fuel pump assembly is replaced, also replace the retainer with a new one (green colored retainer).
• To keep the connecting portion clean and to avoid damage and foreign materials, cover them completely with plastic bags or something similar.
7. Remove the lock ring using a socket drive handle and Tool as shown.
Tool number : KV991J0090 (J-46214)
CAUTION: • Discard the lock ring, do not reuse the lock ring.
• Discard the ring seal, do not reuse the ring seal.
8. Remove the fuel level sensor, fuel filter, and fuel pump assembly.
CAUTION: • Do not bend the float arm during removal.
• Discard the ring seal, do not reuse the ring seal.
INSPECTION AFTER REMOVAL
Inspect the fuel level sensor, fuel filter, and fuel pump for any defects and foreign materials. Replace as necessary.
INSTALLATION
Installation is in the reverse order of removal.
• Install the fuel level sensor, fuel filter, and fuel pump assembly with the fuel feed hose facing the front of the vehicle as shown. Use a new ring seal.
• Connect the quick connector as follows: - Check the connection for damage or any foreign materials.
- Align the connector with the tube, then insert the connector straight into the tube until a click is heard.
• After the tube is connected, make sure the connection is secure by performing the following checks: - Pull the tube and the connector to make sure they are securely connected.
- Visually confirm that the two retainer tabs are connected to the quick connector.
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
1. Turn the ignition switch to ON (without starting the engine) to apply fuel pressure to the fuel system, then check the connections for fuel leaks.
2. Start the engine and let it idle and check for fuel leaks at the fuel system connections.
Inspection
INSPECTION AFTER INSTALLATION
Use the following procedure to check for fuel leaks.
1. Turn ignition switch “ON” (with engine stopped), then check connections for leaks by applying fuel pressure to fuel piping.
2. Start engine and let it idle and make sure there are no fuel leaks at the fuel system connections.
Fuel tank
Exploded View
1. Lock ring
2. Fuel level sensor, fuel filter, and fuel
pump assembly
3. Seal ring
4. Fuel tank mounting straps
5. Fuel tank protector
6. Fuel tank
7. Fuel filler hose
8. Fu ...
Other materials:
P1715 input speed sensor (primary
speed sensor)
Description
ECM receives primary speed sensor signal from TCM through CAN communication
line. ECM uses this signal
for engine control.
DTC Logic
DTC DETECTION LOGIC
NOTE:
• If DTC P1715 is displayed with DTC UXXXX, first perform the trouble diagnosis
for DTC UXXXX.
• If DTC P1715 is ...
BCM branch line circuit
Diagnosis Procedure
INSPECTION PROCEDURE
1.CHECK CONNECTOR
1. Turn the ignition switch OFF.
2. Disconnect the battery cable from the negative terminal.
3. Check the terminals and connectors of the BCM for damage, bend and loose
connection (unit side and
connector side).
Is the inspec ...
Headlight control switch
Lighting
1 When turning the switch to the
position,
the front parking, tail, license plate and
instrument panel lights come on.
2 When turning the switch to the
position,
the headlights come on and all the other
lights remain on.
CAUTION
Use the headlights with the engine running
to a ...