Nissan Altima 2007-2012 Service Manual: P0643 Sensor power supply

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

TESTING CONDITION: Before performing the following procedure, confirm that battery voltage is more than 8V at idle.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

1. Start engine and let it idle for 1 second.

2. Check DTC.

Is DTC detected? YES >> Go to EC-362, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK GROUND CONNECTION

1. Turn ignition switch OFF.

2. Check ground connection E9. Refer to Ground Inspection in GI-45, "Circuit Inspection".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace ground connection.

2.CHECK ACCELERATOR PEDAL POSITION SENSOR 1 POWER SUPPLY CIRCUIT

1. Disconnect accelerator pedal position (APP) sensor harness connector.

2. Turn ignition switch ON.

3. Check the voltage between APP sensor harness connector and ground.

Is the inspection result normal? YES >> GO TO 7.

NO >> GO TO 3.

3.CHECK SENSOR POWER SUPPLY CIRCUITS

Check harness for short to power and short to ground, between the following terminals.

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair short to ground or short to power in harness or connectors.

4.CHECK COMPONENTS

Check the following.

• Battery current sensor (Refer to EC-380, "Component Inspection".) • Power steering pressure sensor (Refer to EC-355, "Component Inspection".) • Camshaft position sensor (PHASE) (Refer to EC-284, "Component Inspection".) Is the inspection result normal? YES >> GO TO 5.

NO >> Replace malfunctioning component.

5.CHECK TP SENSOR

Refer to EC-191, "Component Inspection".

Is the inspection result normal? YES >> GO TO 9.

NO >> GO TO 6.

6.REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR

1. Replace electric throttle control actuator.

2. Go to EC-29, "ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair Requirement".

>> INSPECTION END

7.CHECK APP SENSOR

Refer to EC-429, "Component Inspection".

Is the inspection result normal? YES >> GO TO 9.

NO >> GO TO 8.

8.REPLACE ACCELERATOR PEDAL ASSEMBLY

1. Replace accelerator pedal assembly.

2. Go to EC-29, "ACCELERATOR PEDAL RELEASED POSITION LEARNING : Special Repair Requirement".

>> INSPECTION END

9.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident".

>> INSPECTION END

    P0607 ECM
    Description CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle multiplex communication line with high data communication speed and excelle ...

    P0850 PNP Switch
    Description When the shift lever position is P or N (CVT), Neutral position (M/T), park/neutral position (PNP) switch is ON. ECM detects the position because the continuity of the line (the ON s ...

    Other materials:

    Ignition coil
    Exploded View 1. Ignition coil 2. Spark plug 3. Rocker cover (RH) 4. Rocker cover (LH) Removal and Installation LH REMOVAL 1. Remove engine room cover. 2. Disconnect ignition coil connector. 3. Remove the ignition coil. CAUTION: Never shock ignition coil. INSTALLATION Installatio ...

    Heater operation
    Heating This mode is used to direct heated air to the foot outlets. Some air also flows from the defrost outlets and the side vent outlets. 1. Press the button to the OFF position for normal heating. 2. Press  the air flow control button. 3. Turn the fan control dial to the desired ...

    Stall test
    Inspection and Judgment INSPECTION 1. Inspect the amount of engine oil. Replenish the engine oil if necessary. 2. Drive for about 10 minutes to warm up the vehicle so that the CVT fluid temperature is 50 to 80°C (122 to 176°F). Inspect the amount of CVT fluid. Replenish if necessary. 3. ...