Nissan Altima 2007-2012 Service Manual: Power window main switch
Description
• BCM supplies power.
• It operates each power window motor via corresponding power window switch and makes window move up/ down when main power window and door lock/unlock switch is operated.
Component Function Check
Main Power Window And Door Lock/unlock Switch
1. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH FUNCTION
Does power window motor operate with main power window and door lock/unlock switch operation? Is the inspection result normal? YES >> Main power window and door lock/unlock switch power supply and ground circuit are OK.
NO >> Refer to PWC-303, "POWER WINDOW MAIN SWITCH : Diagnosis Procedure".
Diagnosis Procedure
Main Power Window And Door Lock/unlock Switch Power Supply Circuit Check
1. CHECK POWER SUPPLY CIRCUIT
1. Turn ignition switch ON.
2. Check voltage between main power window and door lock/ unlock switch connectors (A and B) and ground.
Is the measurement value within the specification? YES >> GO TO 3
NO >> GO TO 2
2. CHECK HARNESS CONTINUITY
1. Turn ignition switch OFF.
2. Disconnect BCM and main power window and door lock/unlock switch.
3. Check continuity between BCM connector (A) and main power window and door lock/unlock switch connectors (B and C).
4. Check continuity between BCM connector (A) and ground.
Is the inspection result normal? YES >> GO TO 4
NO >> Repair or replace harness.
3. CHECK GROUND CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect main power window and door lock/unlock switch.
3. Check continuity between main power window and door lock/ unlock switch connector and ground.
Is the inspection result normal? YES >> Replace main power window and door lock/unlock switch. Refer to PWC-411, "Removal and Installation".
After that, refer to PWC-307, "POWER WINDOW MAIN SWITCH : Special Repair Requirement".
NO >> Repair or replace harness.
4. CHECK BCM OUTPUT SIGNAL
1. Connect BCM.
2. Turn ignition switch ON.
3. Check voltage between BCM connector and ground.
Is the measurement value within the specification? YES >> Check main power window and door lock/unlock switch output signal (rear power window switch LH) GO TO 5
YES >> Check main power window and door lock/unlock switch output signal (rear power window switch RH) GO TO 6
NO >> Replace BCM. Refer to BCS-96, "Removal and Installation".
5. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OUTPUT SIGNAL (REAR POWER WINDOW SWITCH LH)
1. Turn ignition switch ON.
2. Check voltage between main power window and door lock/ unlock switch connector and ground.
Is the measurement value within the specification? YES >> GO TO 7
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-411, "Removal and Installation". After that, refer to PWC-307, "POWER WINDOW MAIN SWITCH : Special Repair Requirement".
6. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH OUTPUT SIGNAL (REAR POWER WINDOW SWITCH RH)
1. Turn ignition switch ON.
2. Check voltage between main power window and door lock/ unlock switch connector and ground.
Is the measurement value within the specification? YES >> GO TO 8
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-411, "Removal and Installation".
7. CHECK HARNESS CONTINUITY (REAR POWER WINDOW SWITCH LH)
1. Turn ignition switch OFF.
2. Disconnect rear power window switch LH.
3. Check continuity between main power window and door lock/ unlock switch connector and rear power window switch LH connector.
4. Check continuity between main power window and door lock/unlock switch connector and ground.
Is the inspection result normal? YES >> GO TO 9
NO >> Repair or replace harness.
8. CHECK HARNESS CONTINUITY (REAR POWER WINDOW SWITCH RH)
1. Turn ignition switch OFF.
2. Disconnect rear power window switch RH.
3. Check continuity between main power window and door lock/ unlock switch connector and rear power window switch RH connector.
4. Check continuity between main power window and door lock/unlock switch connector and ground.
Is the inspection result normal? YES >> GO TO 9
NO >> Repair or replace harness.
9. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH
Check main power window and door lock/unlock switch.
Refer to PWC-306, "POWER WINDOW MAIN SWITCH : Component Inspection".
Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-411, "Removal and Installation"..After that, refer to PWC-307, "POWER WINDOW MAIN SWITCH : Special Repair Requirement".
Component Inspection
1. CHECK MAIN POWER WINDOW AND DOOR LOCK/UNLOCK SWITCH
1. Check main power window and door lock/unlock switch.
2. Check continuity between main power window and door lock/ unlock switch (power window lock switch). (Lock operation).
3. Check continuity between main power window and door lock/ unlock switch (power window lock switch). (Unlock operation).
Is the inspection result normal? YES >> Main power window and door lock/unlock switch is OK.
NO >> Replace main power window and door lock/unlock switch. Refer to PWC-411, "Removal and Installation". After that, refer to PWC-307, "POWER WINDOW MAIN SWITCH : Special Repair Requirement".
Special Repair Requirement
1. PERFORM INITIALIZATION PROCEDURE
Perform initialization procedure.
Refer to PWC-295, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".
Is the inspection result normal? YES >> GO TO 2
NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
2. CHECK ANTI-PINCH OPERATION
Check anti-pinch operation.
Refer to PWC-295, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Requirement".
Is the inspection result normal? YES >> Inspection end.
NO >> Refer to PWC-320, "DRIVER SIDE : Component Function Check".
Front power window switch
Description
• BCM supplies power.
• Front power window motor RH will be operated if power window and door
lock/unlock switch RH is operated.
Component Function Check
Power Window An ...
Other materials:
Basic inspection
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
DETAILED FLOW
1.OBTAIN INFORMATION ABOUT SYMPTOM
Interview the customer to obtain as much information as possible about the
conditions and environment under
which the malfunction occurred.
>> GO TO 2
2.CHECK SYMPTOM
• Check the symptom bas ...
Basic inspection
DIAGNOSIS AND REPAIR WORKFLOW
Work Flow
DETAILED FLOW
1.CONFIRM SYMPTOM
Confirm symptom or customer complaint.
>> GO TO 2
2.CHECK SELF-DIAGNOSIS OPERATION OF COMBINATION METER
Perform self-diagnosis of combination meter. Refer to MWI-38, "Diagnosis
Description".
Does s ...
Intelligent key system/engine start function symptoms
Symptom Table
Engine cannot be started with all Intelligent Keys.
CAUTION:
• Follow Trouble Diagnosis Flowchart referring to “SEC-10, "Work Flow"”.
Determine malfunctioning
condition before performing this diagnosis.
• Check that vehicle is under the condition shown in “ ...